What Causes Corrosion Inside Household Water Pipes

Plumbing Tips

TL;DR

  • Pipe corrosion is caused by a mix of water chemistry, pipe material, water pressure, temperature, and microbial activity — often working together.
  • Galvanised steel pipes corrode from the inside out. By the time you see symptoms at the tap, the damage is usually well advanced.
  • Sydney’s mains water is mildly corrosive to older metal pipes, particularly galvanised steel and some copper installations.
  • The warning signs — brown water, low pressure, blue-green staining, recurring leaks — are symptoms of a process that’s been underway for years.
  • Corrosion doesn’t fix itself. The earlier you get it assessed, the more options you have.

The problem that builds before you notice it

Most homeowners don’t think about pipe corrosion until something goes wrong: a pinhole leak in the wall, brown water at the kitchen tap, or a pressure drop that keeps getting worse. By that point, the corrosion has usually been active for years.

Understanding what actually causes it — and why some homes are more vulnerable than others — helps you catch it earlier and make smarter decisions about repair or replacement.

Cause 1: Water chemistry and pH

The chemistry of the water flowing through your pipes matters more than most people realise. Water that sits toward the acidic end of the pH scale is aggressive toward metal pipes, particularly copper and galvanised steel. It slowly strips material from the pipe wall with every litre that passes through.

Sydney’s mains water is generally treated to sit within a safe pH range, but the chemistry can shift slightly depending on your suburb, the season, and how far the water travels through the distribution network before it reaches your property. Older homes at the end of long supply runs sometimes see slightly more aggressive water chemistry than newer estates closer to treatment infrastructure.

High chloride or sulfate content in the water supply can have a similar effect, weakening pipe material over time and accelerating the corrosion process, particularly at joints and fittings where flow changes direction.

Cause 2: Dissolved oxygen in the water supply

Household water is oxygenated. That oxygen reacts with metal through a process called oxidation, which is the same chemical process that turns iron into rust. Inside a galvanised steel pipe, this reaction happens slowly and continuously. The zinc coating that protects the steel buys time, but once it’s gone, the steel beneath corrodes at a faster rate.

Higher water temperatures accelerate this process. Hot water lines in older homes tend to show corrosion damage earlier and more severely than cold supply lines, for exactly this reason. If your hot water is the first tap to run discoloured in the morning, that’s a useful clue about where the damage is concentrated.

Cause 3: Pipe material and age

Not all pipes corrode at the same rate or in the same way. The material is one of the biggest variables.

Galvanised steel

Galvanised steel pipes were standard in Sydney homes built before the 1970s. The zinc coating slows corrosion initially, but it degrades over decades. Once it’s gone, the steel corrodes from the inside out — narrowing the pipe bore, reducing pressure, and eventually causing leaks or discoloured water. By the time you see the signs at the tap, the interior of the pipe is often already significantly restricted or damaged. If your home still has galvanised supply pipes, see our guide on galvanised pipes in older Sydney homes for a closer look at the failure patterns.

Copper

Copper is more corrosion-resistant than galvanised steel, but it’s not immune. Acidic water, high dissolved oxygen, and high water velocity can all attack copper over time. The visible sign is usually blue-green staining around taps, joints, and fixtures — caused by copper dissolving into the water and depositing on surfaces. If you’re seeing that staining in your home, our post on green and blue stains around taps explains what’s behind it.

PEX and plastic pipe

Modern PEX and PVC pipes don’t corrode in the same way metal pipes do. They’re not immune to degradation — UV exposure, chemical exposure, and very high temperatures can affect them — but internal corrosion from water chemistry is not a meaningful risk with these materials. This is one reason most replumbing work in Sydney now uses PEX or copper rather than galvanised steel.

Cause 4: High water pressure and flow velocity

Water moving through a pipe at high velocity creates turbulence, especially at bends, tees, and partially closed valves. That turbulence physically wears away the pipe wall in a process called erosion corrosion. It’s not just a chemical reaction — it’s mechanical abrasion from the inside.

High water pressure accelerates this. Homes in Sydney that sit on a high-pressure part of the mains network — or that have never had a pressure-limiting valve installed — put more mechanical stress on their pipes with every tap that opens. Over years, that adds up, particularly in undersized pipes where the water has to move faster to deliver the same flow rate.

If your home’s water pressure has always run high and you have older metal pipes, the combination is worth taking seriously.

Cause 5: Electrolytic and galvanic corrosion

When two different metals are connected in a plumbing system — say, copper fittings on galvanised steel pipe — an electrochemical reaction can occur between them. One metal acts as an anode and gives up electrons to the other. The anode corrodes faster than it would on its own.

This is called galvanic corrosion, and it tends to concentrate at the join between the two metals. It’s one reason older homes that have had partial repairs or upgrades over the decades — mixing copper and galvanised steel in the same run — sometimes develop leaks at specific joints rather than along the full length of the pipe.

Stray electrical currents from poor earthing can cause a similar electrochemical reaction, though this is less common in residential properties with modern electrical installations.

Cause 6: Microbial activity inside the pipe

Certain bacteria — particularly iron-oxidising and sulfate-reducing bacteria — can accelerate corrosion through a process called microbiologically influenced corrosion. These microorganisms attach to the pipe wall and form biofilms. The byproducts of their activity are corrosive to the pipe material beneath them.

This is more common in pipes that sit stagnant for periods — holiday homes, infrequently used branches of a plumbing system, or pipes that have already developed rough internal surfaces from early corrosion. Rough surfaces give bacteria more area to colonise, which is one reason corrosion tends to accelerate once it gets a foothold.

Cause 7: Sediment and grit in the water supply

Sediment carried in the water supply acts like fine sandpaper inside the pipe. It’s most damaging at bends and constrictions where the flow changes direction and the particles impact the pipe wall at higher velocity. Over time, this physical erosion thins the pipe wall and creates surface roughness that chemical corrosion can then attack more easily.

This tends to be more relevant after mains disturbances — nearby roadworks, a burst main in the street, or Sydney Water maintenance work — when sediment that’s been sitting in the network gets disturbed and flushed through. If your water runs slightly cloudy or gritty after a mains event nearby, running the cold tap for a few minutes until it clears is worth doing.

Why older Sydney homes are more exposed

The combination of galvanised steel supply pipes, original copper fittings, decades of mains water, and the occasional partial repair using different materials creates ideal conditions for several of these causes to work together. A home built in the 1950s or 1960s that still has its original plumbing has had 60-plus years of oxidation, pressure cycling, and water chemistry acting on the same pipes.

That doesn’t mean the pipes are about to fail tomorrow. But it does mean the margin for error is smaller, and the signs are worth paying attention to rather than waiting out.

What the warning signs actually look like

Pipe corrosion rarely announces itself dramatically. The signs tend to build slowly:

  • Brown or rust-coloured water, especially first thing in the morning or after the water’s been off — a sign of iron corrosion inside galvanised or steel pipes.
  • Blue-green staining around taps, in the sink basin, or on shower fittings — copper dissolving into the water supply.
  • Gradually dropping water pressure across the whole house, not just one fixture — the pipe bore narrowing from internal buildup.
  • Recurring leaks at the same section of pipe — the wall has thinned to the point where pressure is finding weak spots.
  • A metallic taste in the water, particularly from the hot tap.

If you’re seeing more than one of these, the pipes are telling you something. For a fuller picture of what the signs mean, this guide on signs your home needs new water pipes covers the decision-making side in more detail.

What you can check yourself

A few things are worth looking at before you call anyone:

  • Run the cold kitchen tap first thing in the morning before any other water has been used. If it runs brown for the first few seconds then clears, the corrosion is likely localised to a specific section of pipe rather than the full supply run.
  • Check exposed pipes under the sink or in the roof space for visible corrosion, discolouration, or white and green crust at joints.
  • Note whether the pressure drop or discolouration is on the hot side only, the cold side only, or both — that narrows the location significantly.
  • Check your water meter for movement when all taps are off. If the dial is moving, there’s a leak somewhere in the system, which could be corrosion-related.

When to stop watching and call a plumber

If the water is consistently discoloured, the pressure has dropped noticeably across the house, or you’ve had more than one unexplained leak in the same run of pipe in the past couple of years, it’s time to get the pipes properly assessed rather than waiting for the next problem.

A licensed plumber can inspect the exposed sections, run a pressure test, and in some cases use a pipe camera to look at the internal condition of the pipe without opening walls. That gives you a clear picture of what you’re actually dealing with — and whether you’re looking at a targeted repair or a broader replacement.

Corrosion doesn’t reverse. The question is always whether you’re catching it early enough to have options, or late enough that the decision’s been made for you.

If you’d like us to take a look, call Bill and the team at Jasco Plumbing. We’ll tell you what we find, give you a fixed price before any work starts, and leave the site clean when we’re done.

GOT A PROBLEM? WE'VE GOT A PLUMBER.

Give us a call or book online. We're across the whole Sydney Region, 7 days a week – ready when you need us.