Leaking Hot Water Tank: Emergency or Wait Until Morning?

Plumbing Tips

TL;DR

  • Where the water is coming from is the single most important clue. Location decides urgency more than volume.
  • Water from the tank body itself, pooling under the unit, or anywhere near electrics: isolate the system now and call tonight.
  • A slow drip from the temperature and pressure relief valve drain pipe during or after heating is often normal — but it still needs a plumber to confirm.
  • Before you do anything else, turn off the cold water inlet to the unit and switch off the power or gas. That step is always right, regardless of severity.
  • If you can isolate the leak and there’s no water near electrics, no gas smell, and no active flooding, a same-day booking in the morning is usually fine.

The question most people ask at the wrong moment

You’ve just found a puddle under your hot water system. It’s 10pm. You’re trying to work out whether this is a “call someone now” situation or a “book it in the morning” situation.

The honest answer: it depends on one thing more than anything else. Not how much water there is. Not how old the unit is. It’s where the water is actually coming from.

A storage hot water tank holds 125 to 315 litres of water depending on the size. If the tank body fails, that water comes out fast and it doesn’t stop until the tank is empty or the supply is shut off. That’s a different situation entirely from a fitting that’s weeping at a joint.

So before you decide anything, spend two minutes working out the source.

Step one: isolate the system first, then look

Whatever you find, do this before you investigate further:

  1. Turn off the cold water inlet valve at the top or side of the unit. Turn it clockwise until it stops. If that valve is seized or missing, go to the mains stop tap at your front boundary instead.
  2. Switch off the power or gas. For electric systems, go to your switchboard and turn off the hot water circuit. For gas systems, turn the gas valve at the unit to the off position.

This matters even if the leak looks minor. An electric element left energised in a draining tank will burn out within minutes. A gas burner running on a system that’s losing water creates its own problems. Isolating takes thirty seconds and removes the risk while you assess.

Now: where is the water actually coming from?

Walk around the unit and look carefully. The location tells you almost everything.

Water from the tank body or base of the outer casing

This is the one to take most seriously. Water seeping from under the outer jacket when you can’t trace it to a fitting, valve, or drain line above suggests the inner tank has started to fail. A tank leak of this kind cannot be repaired — the unit needs replacing.

More importantly, a tank that has started leaking from the body tends to worsen without warning. A typical storage tank holds well over a hundred litres. If the breach expands overnight, it can flood a laundry, garage, or under-house space in minutes.

Call tonight. Don’t wait until morning.

Water pooling under the unit with no clear source above

If you can see water sitting on the floor beneath the unit but can’t trace it to a specific fitting or valve, treat it the same way. You can’t confirm it isn’t the tank body from the outside. Until a plumber opens it up and checks, assume the worst-case scenario and act accordingly.

Call tonight.

Water near any electrical component

If water is near the unit’s electrical cover, a nearby power point, the switchboard, or any wiring, don’t touch anything. Step back, turn off the power at the switchboard if you can do so safely without stepping through water, and call immediately. Water and live electrics in the same space is a safety issue that overrides every other consideration.

Call tonight. This is an emergency.

A gas smell near the unit

Don’t investigate further. Leave the area, don’t operate any switches or lights, and call the gas emergency line (Jemena Gas Networks: 131 909 for NSW) from outside. Once the gas is made safe, call a licensed plumber.

This is an emergency. Leave first, call from outside.

Water dripping from the temperature and pressure relief valve drain pipe

Most storage hot water systems have a T&P relief valve on the side or top of the unit, with a small pipe running down to a drain or outside. A small amount of water from this pipe during or just after the system heats is often normal — the system is releasing a small volume as the water expands inside the tank.

What’s not normal: the valve running continuously, releasing hot or steaming water, or discharging more than a small amount. A T&P valve that runs all the time usually means the valve itself has failed, or the system pressure is too high. Either way, it needs attention — but if it’s a slow, intermittent drip and the system is otherwise stable, this is typically a same-day booking rather than a midnight callout.

Isolate and book a morning visit, unless the flow is continuous or the water is hot and steaming.

Water at the cold water inlet or hot water outlet connections at the top

Fittings and connections at the top of the unit can work loose over time, especially on older systems. A weeping joint at the top is usually a fitting or valve issue rather than a tank failure. Isolate the water supply, check whether the drip stops once the inlet is closed, and book a plumber for the morning.

Morning booking is usually fine if the drip stops when the inlet is closed.

Water from the drain valve near the base

Storage systems have a drain valve low on the tank body. These valves can fail or weep over time. A drip from a drain valve is different from a tank body leak — the valve can often be replaced without replacing the whole unit. Isolate the system and book a morning visit.

Morning booking is usually appropriate.

A quick decision guide

What you’re seeing Urgency What to do
Water from the tank body or base casing Emergency Isolate now, call tonight
Water pooling under unit, source unclear Emergency Isolate now, call tonight
Water near electrics or switchboard Emergency Isolate power if safe, call tonight
Gas smell near the unit Emergency Leave, call gas line from outside
T&P valve running continuously or steaming Urgent Isolate, call tonight or first thing
T&P valve dripping intermittently during heating Same day Isolate, book morning visit
Weeping fitting or connection at the top Same day Isolate, book morning visit
Dripping drain valve near the base Same day Isolate, book morning visit

What about the unit being inside the house?

Location of the hot water system changes the stakes. A unit installed in a laundry, hallway cupboard, or ceiling space has far less tolerance for a slow leak than one sitting on a concrete pad outside. Water inside the house can get into floors, walls, and ceiling cavities quickly. If your unit is indoors and you’re seeing any active leak — even a slow one — lean toward calling sooner rather than waiting.

Can a leaking hot water tank be repaired?

It depends on where the leak is. Fittings, valves, and drain valve failures can often be repaired or the component replaced. A leak from the tank body itself is a different story — the inner tank has corroded or cracked, and that’s not something that can be patched. A tank leaking from the body needs replacing.

This is worth knowing because it changes the conversation when you call. If you can tell the plumber that water is coming from the base of the tank versus a fitting at the top, they can give you a more accurate picture of what to expect before they arrive.

What to do while you wait

Once the system is isolated, there are a few practical things worth doing before the plumber arrives:

  • Mop up what’s already on the floor to prevent it spreading into walls or under flooring.
  • Photograph everything — the unit, the source of the leak, and any water damage on the floor or walls. This is useful for insurance if the damage turns out to be significant.
  • Note the age of the unit if you can find it. The serial number or installation date is usually on a label on the tank. A plumber will ask, and it affects whether repair or replacement makes more sense.
  • Check whether the hot water circuit breaker has tripped on electric systems. If it has, leave it off until the plumber confirms it’s safe to restore.

One thing worth knowing about after-hours callouts

After-hours plumbing costs more than a daytime booking. That’s a real consideration. But the cost of water damage to a floor, wall, or ceiling cavity is almost always higher than an after-hours callout. If you’re genuinely unsure whether your situation qualifies, our post on when an after-hours plumber is worth the call walks through the decision in more detail.

The short version: if you can isolate the leak, there’s no active flooding, no gas smell, and no water near electrics, you can usually wait until morning. If any of those conditions aren’t met, call now.

Ready to get it sorted?

If your hot water tank is leaking and you’re not sure what you’re looking at, call us and describe what you see. We can help you work out whether it needs attention tonight or whether a same-day booking in the morning will do. For confirmed emergencies, we’re available 24/7 across Sydney.

For hot water repairs and replacements, see our hot water systems service page for what we cover and how we work.

GOT A PROBLEM? WE'VE GOT A PLUMBER.

Give us a call or book online. We're across the whole Sydney Region, 7 days a week – ready when you need us.