Wastewater in Your Garage During a Storm: What to Do

Plumbing Tips

TL;DR

  • Wastewater in your garage during a storm is a health hazard. Treat it as an emergency, not a cleanup job.
  • Stop using all water inside the house immediately. Every flush and every tap adds volume to a system that’s already overwhelmed.
  • Keep people and pets out of the affected area until it’s been cleaned and the source is confirmed.
  • If water is near any power point, switch board, or electrical fitting, cut power to that area at the switchboard before you go anywhere near it.
  • The cause is almost always one of three things: your overflow relief gully doing its job, a blockage in your private sewer line, or a cross-connection between your stormwater and sewer systems.
  • You need a licensed plumber to confirm the source and fix it. This is not a mop-and-move-on situation.

Why the garage is a common entry point

Garages sit low. In a lot of Sydney homes, especially older ones in areas like Botany, Mascot, Earlwood, and the inner west, the garage floor is the lowest point on the property. That matters because when a sewer system backs up, wastewater always finds the lowest exit it can. If your garage has a floor waste connected to the sewer, that drain is often the first place it surfaces.

The water appearing in your garage isn’t random. During intense Sydney storms, surging water can cause backflow, where water is pushed up instead of draining away, and this is particularly dangerous when it becomes sewer backflow. Your garage floor waste is simply where that pressure finds its way out.

Step 1: Get people and pets out of the garage now

Wastewater isn’t just unpleasant. It contains bacteria, pathogens, and contaminants that are a genuine health risk. Don’t let kids or pets anywhere near it. If you need to walk through to reach a valve or switchboard, wear rubber boots and wash your hands thoroughly after.

Sewage overflows can damage flooring, walls, and electrical systems, and wastewater can penetrate porous materials, potentially causing structural deterioration, persistent odours, and mould growth if not properly cleaned and dried. The faster you contain the situation, the less of that you’ll deal with.

Step 2: Check for electricity near the water

Before anything else, look at where the water is sitting. Is it near a power point? Close to the switchboard? Near any electrical fitting on the garage wall or ceiling? If the answer is yes, go to your main switchboard and turn off the circuit that covers the garage. Don’t touch switches or fittings in the affected area with wet hands. Water and electricity near a sewer overflow is a serious risk, not a secondary concern.

Step 3: Stop using water inside the house

Tell everyone in the house: no flushing toilets, no running taps, no showers, no dishwasher, no washing machine. Stopping all water use immediately is the single most important first action you can take when sewage is backing up. Every litre you add to the system pushes more wastewater out through the path of least resistance, which right now is your garage floor.

Step 4: Find your overflow relief gully and check it

Your overflow relief gully (ORG) is a fitting in your yard, usually near the back or side of the house, that’s designed to release sewer pressure before it reaches your indoor fixtures. In NSW, the gully must sit at least 150mm below the lowest fixture and at least 75mm above finished ground level.

Check whether your ORG is overflowing outside. If it is, that’s actually the system working as intended: it’s releasing pressure in the yard rather than letting it back up inside the house. But if the ORG is overflowing and wastewater is still entering the garage, the volume is too much for the ORG alone to handle, or there’s a separate issue with the garage floor waste connection.

If the ORG is blocked, covered, or buried under paving, it can’t do its job. An important piece of plumbing that prevents sewage overflows inside homes is frequently covered up by pot plants, mats, concrete, or paving. If it’s covered, it won’t be able to do its job and sewage can overflow inside your home.

For more on what the ORG does and why it overflows, read our post on overflow relief gully overflows and what they mean.

What’s actually causing it: the three most likely reasons

1. The sewer system is overwhelmed by rain

Heavy rainfall can overload the municipal sewer system, forcing wastewater back through private connections. When the public main is under pressure, your ORG may overflow even though nothing is wrong with your private pipes. In this case, the backup eases once the storm passes and the network drains down. You still need it checked, but it may not point to a fault on your property.

2. A blockage in your private sewer line

If your pipes were already partially blocked before the storm, even normal household use can push the system over the edge when rain adds extra load. A pipe does not need to be fully blocked to cause trouble. Water may still pass through a restricted opening on a dry day. Once rainfall adds extra volume, that opening is no longer large enough. Tree roots, grease buildup, and debris are the common culprits. The storm didn’t cause the blockage; it just exposed it.

3. A cross-connection between your stormwater and sewer systems

This is the cause that keeps coming back every time it rains. If your drains only back up during or immediately after heavy rain, an incorrect stormwater-to-sewer connection may be the underlying cause. During a heavy rain event, massive volumes of clean water flood the sewer network. This overwhelms treatment plants and can cause sewage to back up into homes and overflow into the environment.

Cross-connections often happen because a downpipe or surface drain was mistakenly connected to the sewer line rather than the stormwater system during an old renovation or extension. A cross-connection is both illegal and dangerous. It can send untreated sewage into local waterways or overload the sewer system during heavy rain, causing backups into homes. If you are seeing water back up from your toilet or shower when it rains, that can indicate the stormwater and sewer systems have been incorrectly connected. This is a compliance issue under NSW plumbing standards.

For a full explanation of how these systems work and why they must stay separate, see our guide to sewer and stormwater cross-connections in Sydney homes.

Step 5: Photograph everything before you clean up

Before you mop, move anything, or hose the floor down, take photos and video of the affected area. Show where the water entered, how far it spread, what it reached, and the condition of the floor and walls. This documentation matters for your home insurer. Cleaning up first and claiming later is a common mistake that weakens your position.

Step 6: Call a licensed plumber

Once you’ve stopped water use, cleared people out, and documented the damage, call a licensed plumber. Don’t wait until the storm passes to see if it fixes itself. If sewage is coming up through a drain inside your home, treat it as urgent.

When you call, tell the plumber: where the water is entering, whether the ORG outside is also overflowing, how long the storm has been running, and whether this has happened before. That information helps them arrive with the right gear and shortens the diagnosis.

The plumber will likely run a CCTV inspection through your sewer line to find the blockage or confirm a cross-connection. Properties experiencing drainage problems after every major rain event often benefit from a CCTV inspection rather than repeated drain clearing. Clearing the pipe without knowing why it backed up just means the same thing happens next storm.

You can reach us any time on our blocked drains service page, including after hours.

Step 7: Clean and dry the garage properly

Once the plumber has confirmed the source is contained and the system is clear, the cleanup starts. Wastewater contamination needs more than a mop. You’ll need to disinfect the floor and any surfaces the water contacted, remove anything porous that absorbed wastewater (cardboard, fabric, timber), and dry the area thoroughly. A wet/dry vacuum helps with residual water in floor waste channels. If the water sat for more than a few hours, treat mould prevention as a priority, not an afterthought.

How to reduce the risk before the next storm

The most useful thing you can do after an event like this is get the drainage system properly assessed. Not just cleared, assessed. A CCTV inspection will show whether there’s a partial blockage building, a cross-connection, or a structural defect in the sewer line. Catching these between storms is far less disruptive than dealing with another backup mid-downpour.

A few practical steps worth taking:

  • Confirm your ORG is visible, accessible, and not buried under paving or garden beds.
  • Check whether any downpipes on your property connect underground to a pipe you can’t identify. If you’re not sure where they go, a plumber can trace them.
  • If you have an older home with clay sewer pipes and large trees in the yard, get the lines inspected annually. Tree roots are a slow, predictable problem that CCTV catches early.
  • Know where your main water shut-off valve is so you can isolate the supply fast next time.

When to call Sydney Water instead of a plumber

If multiple neighbouring properties are affected or street drains are backing up, the issue may be in the public stormwater system. Sydney Water is responsible for blockages beyond the property connection point, while internal pipes are the homeowner’s responsibility. If your neighbours are reporting the same issue at the same time, call Sydney Water on 13 20 90 as well as your plumber. It may be a shared main problem, in which case Sydney Water needs to know about it.

If the blockage is confirmed to be on your side of the connection, that’s your responsibility to fix. In Sydney, the private sewer pipe runs to where your pipes join Sydney Water’s main. If the blockage turns out to be in the authority’s main, your plumber will tell you and the authority takes it from there.

The honest takeaway

Wastewater in your garage during a storm is not a weather problem. The storm may have triggered it, but the underlying cause is almost always a blockage, a structural defect, or a cross-connection that was already there. Getting it properly diagnosed after the event is what breaks the cycle. If this has happened more than once, that’s the system telling you something needs fixing, not just clearing.

If you’re dealing with this now or want the drainage system checked before the next storm season, get in touch with Jasco Plumbing. We’re available 24/7 for emergencies across Sydney.

GOT A PROBLEM? WE'VE GOT A PLUMBER.

Give us a call or book online. We're across the whole Sydney Region, 7 days a week – ready when you need us.