TL;DR
- Converting from electric to gas cooking is not a direct swap. It involves a gas supply check, benchtop assessment, ventilation review, and licensed electrical isolation — before you buy anything.
- In NSW, all gas cooktop connections must be done by a licensed gas fitter. DIY is illegal, voids your insurance, and can be dangerous.
- You’ll also need a licensed electrician to disconnect the existing electric cooktop circuit.
- Get the gas supply and installation space assessed before you choose a model or order a cooktop.
- At the end of the job, your gas fitter must issue a Certificate of Compliance — this is a legal requirement, not an optional extra.
This conversion is more involved than most people expect
Gas cooking is popular for good reason: precise heat, instant response, and it works during a power outage. But switching from an electric cooktop to gas is not as simple as pulling one out and dropping another in. The benchtop opening might be a different size. There may be no gas supply in the kitchen at all. The rangehood might not meet the ventilation requirements for a gas appliance. And two separate licensed trades need to be involved.
Getting this wrong is expensive. Getting it right starts with a few checks before you spend a dollar on appliances.
Check 1: Do you actually have a usable gas supply?
This is the first question, and the one most people skip. A gas main running down your street does not mean your kitchen has a usable connection. A gas main in the street does not mean the property has a usable connection — a licensed gas fitter must check the connection, gas type, available capacity, and whether the existing pipework can supply the new appliance.
If you have no gas connection at all, a new line will need to be run from the meter to the kitchen. That adds scope, cost, and time to the job. Find this out before you fall in love with a particular cooktop model.
If you’re on LPG (bottled gas) rather than mains natural gas, that’s a different setup entirely. Natural gas and LPG run at different pressures and need different injectors. The cooktop must be configured for the right gas type, and that configuration has to be done by a licensed gas fitter.
Check 2: Is the existing gas line sized correctly for a cooktop?
Even if you have a gas meter and gas already running to other appliances in the house, the existing pipework may not be sized to supply a cooktop as well. Commercial-style hobs draw more megajoules per hour than a standard four-burner cooktop, and larger lines or upgraded metres can be required. Even standard residential cooktops add load to the gas supply, and the existing pipe diameter needs to be confirmed as adequate before anything is connected.
This is part of what the gas fitter assesses before the job starts — not something you can work out yourself from looking at the meter.
Check 3: The benchtop opening and cabinetry
Electric cooktops and gas cooktops are rarely the same dimensions. The cut-out in your benchtop may be too small, too large, or the wrong shape for the gas model you’re considering. Converting an electric cooktop to gas requires a suitable gas supply, cabinetry assessment, ventilation review, and licensed electrical isolation.
Check the cut-out dimensions of any gas cooktop you’re considering against the existing opening before you buy. If the benchtop needs cutting or modification, that may involve a joiner or benchtop specialist in addition to the gas fitter and electrician. Factor that in early.
Also check the clearances. Built-in gas ovens and freestanding gas cookers require the gas fitter to confirm the appliance clearances to combustible materials meet the manufacturer’s specification and the requirements of AS/NZS 5601.1. Cabinetry that sits close to the cooktop may need to be modified or protected.
Check 4: Ventilation — your rangehood may not be enough
Gas cooking produces combustion byproducts that electric cooking does not. The ventilation requirements are different, and your existing rangehood may not meet them. Australian Standard AS/NZS 5601.1 insists on specific air-exchange levels around gas appliances. If your existing rangehood falls short, a bigger duct or make-up air vent has to be added before the compliance plate is issued.
This is not just a comfort issue — it’s a compliance requirement. The room and rangehood arrangement must satisfy the cooktop manufacturer’s instructions and applicable gas installation requirements. If your kitchen is small or poorly ventilated, get this assessed before committing to the conversion.
Check 5: The electrical side still needs a licensed electrician
Removing an electric cooktop is not as simple as unplugging an appliance. Electric cooktops are hard-wired into a dedicated circuit. That circuit needs to be properly isolated and made safe by a licensed electrician — it cannot simply be left in place or capped off by a gas fitter. A licensed gas fitter must install, connect, test, and commission the gas cooktop. A licensed electrician must disconnect or modify the fixed electric cooktop circuit and assess any electrical supply needed for gas ignition.
Most gas cooktops also require a 240V power point nearby for the ignition system. If there’s no power point in the right location, the electrician will need to install one. For combined installations — say, an electric oven with a gas cooktop — you either need a dual-licensed tradesperson or two separate trades.
Check 6: If you’re in an apartment, strata approval may be required
If you’re in a strata building, check your by-laws before you go any further. Some strata schemes require written approval before any gas work is carried out inside a lot. Others have restrictions on appliance types or require the owners corporation to be notified. Getting this sorted before the trades arrive avoids delays and potential disputes later.
The gas fitter will also need to know where the gas meter and isolation valves are located in your building, and whether there are any access restrictions during the job.
Check 7: Buy the cooktop after the assessment, not before
This is the mistake that catches people out most often. They buy a gas cooktop, then call a gas fitter, only to discover the benchtop opening is wrong, the gas supply needs extending, or the rangehood won’t comply. Have the gas supply and installation space assessed before buying the cooktop.
Once you know what the site can accommodate, you can choose a model that actually fits and works with your existing setup. That assessment can also change what the job costs — so it’s worth having before you’ve already committed to a specific appliance.
What NSW law actually requires
This is not a job you can do yourself, or hand to a general handyman. All gas appliance connections, disconnections, and any associated gas pipework in NSW must be performed by a licensed gas fitter. A standard plumbing licence does not cover gas work — the gas fitter needs a specific gas fitting endorsement on top of their plumbing licence.
You can verify a gas fitter’s licence and endorsement through the Service NSW licence check before anyone starts work. Ask for the licence number when you call.
DIY gas work is illegal, genuinely dangerous, and can void both the appliance warranty and your home insurance.
The Certificate of Compliance: what you get at the end
After any gas installation or repair work in NSW, your licensed gas fitter must issue a Certificate of Compliance for Gas Fitting Work. This document records what work was done, confirms it was completed by a licensed tradesperson, and is required by your insurer if a gas-related claim is ever made.
Keep it with your appliance documents. Connecting a cooktop to an existing gas supply, or extending an existing domestic gas line within the same property, does not require a Development Application in NSW. The Certificate of Compliance issued by the licensed gasfitter is the relevant compliance document.
A quick pre-conversion checklist
- Confirm whether you have a mains gas connection or LPG supply
- Have a licensed gas fitter assess the gas line capacity and route to the kitchen
- Measure the existing benchtop cut-out and compare it to the cooktop you’re considering
- Check the rangehood extraction rate against the manufacturer’s ventilation requirements
- Confirm cabinetry clearances to combustible surfaces
- Arrange a licensed electrician to disconnect the existing electric cooktop circuit
- If in a strata building, check the by-laws and notify the owners corporation if required
- Get the Certificate of Compliance at the end of the job
Ready to get it assessed?
If you’re thinking about switching to gas cooking, the first step is a site assessment — not a trip to the appliance store. Jasco Plumbing holds NSW licence #488187C with a gas fitting endorsement, so the gas side of the job is covered without needing a second trade. We give you a fixed price before any work starts and issue the Certificate of Compliance at the end.
For more on what gas fitting work involves in a Sydney home, read our guide to gas fitting in older Sydney home renovations, or head to our gas fitting services page to find out what we cover and book an assessment.