TL;DR
- A gas bayonet point is the quick-connect outlet on your wall that a portable gas heater or BBQ plugs into. Moving one — even by half a metre — is licensed gas fitting work in NSW. You cannot do it yourself.
- The new location has to comply with AS/NZS 5601.1, which governs where a bayonet point can and cannot go, how far it must sit from doorways, and what ventilation the room needs.
- Bedrooms, bathrooms, hallways, and garages are prohibited locations for unflued gas heater bayonet points.
- Every relocation requires a Certificate of Compliance issued by the licensed gas fitter. That paperwork protects your insurance and proves the work is legal.
- The job itself is usually straightforward when the new point is close to existing pipework. The complications come from location constraints, ventilation requirements, and pipe sizing — all of which a gas fitter assesses before touching anything.
What a gas bayonet point actually is
A gas bayonet fitting is the wall-mounted outlet that lets you connect a portable gas heater or outdoor BBQ directly to your home’s gas supply using a flexible hose. You twist the hose connector in, and the valve opens. Twist it out, and it closes. Simple from the user’s side.
What’s behind the wall is less simple. The bayonet fitting connects to a rigid pipe run that traces back through the wall cavity to your home’s gas supply line. Moving the fitting means moving or extending that pipework — and that’s where the licensed work begins.
Why moving it is always licensed work in NSW
Only licensed gas fitters are legally permitted to perform gas fitting work in NSW, as mandated by the Gas and Electricity (Consumer Safety) Act 2017. That applies whether you’re running a new gas line across the room or shifting an existing bayonet point 30 centimetres to the left.
Adding a new gas outlet for an outdoor kitchen, extending a line for a fireplace, or relocating a stove all require a licensed gas fitter. Even moving the line by half a metre is regulated.
The one thing you can legally do yourself is plug a portable appliance into a bayonet point that’s already installed and compliant. A homeowner can usually do without a licence is plug a portable BBQ into an existing bayonet point that’s already been installed. Everything else, including installing the bayonet itself, requires a licensed gas fitter.
Where a bayonet point can and cannot go
This is the part that catches people off guard. You can’t just pick a new spot on the wall and expect the gas fitter to put the point there. The location has to comply with AS/NZS 5601.1, and some rooms are simply off-limits.
Prohibited locations
Key regulations include prohibited locations: bedrooms, bathrooms, hallways, and garages. These restrictions exist because unflued gas heaters release combustion products directly into the room. In a bedroom, that creates a genuine carbon monoxide risk while people are sleeping. In a bathroom, moisture and confined space compound the danger.
NSW rules do not permit unflued heaters in bedrooms or bathrooms, so a living area is almost always the right home for the point.
Distance from doorways
A licensed gas fitter will ensure compliance with AS/NZS 5601 Part 1 requirements, positioning the connection point at least 1 metre away from doorways. If your preferred new location puts the point too close to a door opening, the gas fitter will tell you before any pipework goes in — not after.
Height requirements
For heater bayonet points, the fitting typically needs to sit at a specific height off the floor to suit the appliance connection. Your gas fitter will confirm the correct height based on the appliance you’re using and what AS/NZS 5601.1 requires for that configuration.
The ventilation requirement people miss
Moving a bayonet point to a new room isn’t just a pipework question. The room itself has to be assessed for ventilation before the gas fitter can sign off on the work.
Connecting flued and unflued gas heaters to new or existing bayonet points requires assessing room ventilation under AS/NZS 5601.1 to confirm that enclosed spaces meet minimum openable area requirements before an unflued appliance operates safely.
AS/NZS 5601.1 requires adequate room ventilation for unflued gas heaters to prevent carbon monoxide buildup, with minimum openable window or permanent vent area calculated based on the appliance’s gas input rating.
In practical terms: if you’re moving a bayonet point to a smaller room, or a room with fewer windows, the gas fitter may need to confirm the room volume is large enough and that there’s sufficient ventilation before the work can proceed. This isn’t bureaucracy — it’s the calculation that determines whether the heater can operate safely in that space.
The 2024 Amendment 2 to AS/NZS 5601.1 also introduced requirements for carbon monoxide detectors under certain conditions involving flueless heaters in living spaces, reflecting the seriousness with which regulators treat location and ventilation together. Your gas fitter will advise if a CO detector is required as part of the job.
What the gas fitter actually checks before moving the point
A competent gas fitter doesn’t just shift the fitting and leave. Before any pipework moves, they’ll assess:
- The new location against AS/NZS 5601.1 rules — prohibited rooms, doorway clearances, and height requirements.
- Room ventilation — whether the new room meets minimum ventilation requirements for the appliance you’re connecting.
- The existing pipe run — condition, sizing, and whether it can be extended to reach the new location without a pressure drop.
- The pipe material in your walls — older Sydney homes sometimes have copper or steel pipework that needs assessment before any extension is made.
- The old bayonet point location — whether the abandoned point needs to be properly capped and what happens to the redundant pipe section.
That last point matters. If the original bayonet point is being removed rather than just relocated, the old pipe end has to be properly capped and tested. You can’t leave an open pipe end in a wall cavity.
What happens to the old point
When you move a bayonet point, the existing outlet doesn’t just disappear. The gas fitter has two options: cap the old point off properly and leave the pipework in place, or remove the redundant pipe run entirely. Which approach makes more sense depends on where the old pipe sits and how the new run is being laid.
Either way, the abandoned end has to be sealed to a standard that passes a pressure test. That pressure test is part of the compliance process — the gas fitter checks the whole installation for leaks before issuing the certificate.
The compliance certificate: what you get and why it matters
After any work involving gas is complete, the licensed gasfitter must give you a certificate of compliance for network gas, or a certificate of inspection for bottled gas.
In NSW, every piece of gasfitting work requires a certificate regardless of cost or property type. For natural gas connections you receive a Certificate of Compliance lodged with Building Commission NSW; for LPG installations you receive a Certificate of Inspection.
From March 2026, all NSW gasfitters must lodge gas compliance and inspection certificates through the BCNSW eCert portal. You should still receive a copy for your own records.
Keep the certificate. If you sell the property, it’s evidence the work was done legally. If your insurer ever questions gas-related damage, the certificate shows the installation was compliant. DIY gas bayonet installation is illegal in NSW and can result in fines, voided insurance, and serious safety hazards including gas leaks and carbon monoxide exposure.
How long the job takes
A straightforward point close to existing pipework takes one to two hours. That covers removing the old fitting, running the new pipe section, installing the new bayonet point, pressure testing the system, and issuing the compliance certificate.
The job takes longer when the new location is further from the existing pipe run, when the wall material makes access harder (think double brick or tiled walls), or when the existing pipework needs attention before the extension can go on. An older Sydney home with steel or corroded copper pipe behind the walls may need more assessment time before the gas fitter can confidently extend from it.
What to sort before the gas fitter arrives
A few things on your end make the visit faster and reduce the chance of a second trip:
- Know which room the new point is going into. Think about where the heater will actually sit, not just where it would be convenient to put the point. Living areas are almost always the right answer for an unflued heater bayonet.
- Note the appliance you’re connecting. If the gas fitter knows the heater model and its gas input rating, they can calculate the ventilation requirement before they arrive.
- Clear wall access at both the old and new locations. If furniture is in the way, move it before the visit. Access to the wall cavity may be needed depending on how the pipe run is laid.
- Know where your gas meter is. The gas fitter will need to isolate the supply before work starts. If the meter is behind a locked gate or inside a cupboard, have it accessible.
- Check the gas fitter’s licence before they start. You can verify any NSW gas fitter’s licence number at NSW Fair Trading’s online licence check. Ask for the number when you book.
For more on what to have ready before a gas fitting visit, see our guide on how to prepare for a gas fitter’s inspection visit.
The one thing you cannot do yourself
It’s worth being clear about this, because the bayonet fitting looks deceptively simple. Plugging a heater hose into the outlet is fine — that’s what it’s designed for. But anything upstream of the bayonet fitting is licensed work. Under the NSW Plumbing and Drainage Act 2011 and the Gas Supply Act 1996, any work on a gas installation, including fitting a single bayonet point, must be carried out by someone holding a current gasfitting licence from NSW Fair Trading.
That includes moving the point, capping the old one, extending the pipe, and testing the system. None of it is a job for a handyman or a general builder. The risks — gas leak, carbon monoxide buildup, voided insurance — are too serious.
Ready to move your gas bayonet point?
If you’re rearranging a room, renovating, or just need the heater connection in a better spot, we can sort it in one visit. Jasco holds NSW licence #488187C, which includes gas fitting endorsement, so there’s no need to book a separate trade.
We’ll assess the new location against AS/NZS 5601.1 requirements, run the pipework, pressure test the system, and hand you the Certificate of Compliance before we leave. Fixed price before we start, no surprises on the bill.
Call us or book through our gas fitting page and tell us what you’re trying to do. We’ll give you a straight answer on whether the new location works and what the job involves.