Green or Blue Stains Around Taps: What They Mean

Plumbing Tips

TL;DR

  • Green or blue stains around taps, sinks, and drains are almost always caused by copper corroding inside your pipes or fittings. The copper dissolves into the water and leaves a blue-green deposit wherever the water sits or dries.
  • Other causes include electrolytic corrosion (two different metals touching in the pipework), mould, or residue from cleaning products — but copper corrosion is the most common by far.
  • In Sydney, the mains water supply is slightly alkaline and generally not aggressive toward copper. If you’re seeing stains, the problem is usually in the pipes, fittings, or tapware itself — not the water quality.
  • Stains are a cosmetic symptom. The real risk is what’s happening inside the pipe: corrosion that, left alone, leads to pinhole leaks and eventually worse.
  • A licensed plumber can identify where the corrosion is coming from and whether the affected pipework needs attention.

You notice a blue-green ring around the base of the tap. Or a greenish smear where the water drains in the bathroom basin. You clean it off, and a few weeks later it’s back. It’s not dirt, and it’s not mould. So what is it?

Most of the time, that colour is telling you something specific about your copper plumbing. Here’s what’s actually going on, what it means for your home, and when it’s worth getting a plumber in.

What causes green and blue stains?

The colour comes from copper. When copper pipes or brass fittings corrode, tiny amounts of copper dissolve into the water passing through them. That water then sits on your tap, your sink basin, or around the drain. When it evaporates, it leaves the copper behind as a blue, green, or turquoise deposit — similar in colour to the patina you see on old copper roofs or statues.

Brass fittings behave the same way. Brass is an alloy of copper and zinc, so when it corrodes, it produces the same blue-green staining.

The stain itself is harmless to touch. The issue is what’s causing it: corrosion inside the pipe or fitting that, over time, thins the metal and creates the conditions for pinhole leaks.

The three main causes in Sydney homes

1. Copper pipe or fitting corrosion

This is the most common cause. Copper pipes corrode when the water passing through them is acidic enough to slowly dissolve the metal. The dissolved copper then leaves a blue-green stain wherever the water rests or dries — around the tap base, inside the basin, or at the drain outlet.

Corrosion also speeds up when water sits stagnant in a pipe for long periods. If a tap or fixture isn’t used much, the water inside has more time to react with the copper wall of the pipe.

New copper pipework can also produce staining in the first few months after installation. The inside surface of fresh copper pipe hasn’t yet developed a stable oxide layer, so it reacts more readily with water until that layer forms.

2. Electrolytic corrosion (dissimilar metals)

When two different metals are connected in your plumbing — say, copper pipe joined directly to a steel fitting without a dielectric union — a small electrical current flows between them in the presence of water. The less chemically stable metal corrodes faster than it would on its own. This is called galvanic or electrolytic corrosion, and it can produce concentrated blue-green staining at or near the join.

It’s more common in older Sydney homes where plumbing has been repaired or extended over the decades using whatever fittings were available at the time. A mix of galvanised steel, copper, and brass in the same system is a common setup in pre-1980s houses.

3. Mould

Some types of mould — particularly those that grow in damp, poorly ventilated areas — can appear blue-green. If the stain is fluffy or velvety in texture, or if it’s growing on the surface of silicone or grout rather than on the porcelain or tap itself, it may be mould rather than copper residue.

The quick test: wipe it with a dry cloth. Copper staining tends to leave a faint blue-green smear on the cloth. Mould tends to come away in a darker, more irregular pattern and often has a musty smell.

What about cleaning products?

Some blue or green toilet bowl cleaners and in-cistern tablets can leave a blue-green tint around the bowl and under the rim. This is dye from the product, not copper corrosion. If you use one of these products and the staining is only in the toilet, that’s the likely explanation. Stop using the product for a few weeks and see whether the colour clears.

A note on Sydney’s water quality

Acidic water is the most common cause of copper corrosion in plumbing internationally. However, Sydney’s mains water supply is slightly alkaline, with a typical pH in the range of 7.5 to 7.8 — well within the safe range and not aggressive toward copper under normal conditions.

This means if you’re seeing blue-green staining in a Sydney home, the mains water supply is probably not the culprit. The more likely causes are the age and condition of your pipes and fittings, the presence of dissimilar metals in the system, or localised issues at specific fixtures.

There are exceptions. Older homes with long pipe runs, homes where water sits stagnant for extended periods (holiday rentals, vacant properties), and properties where the internal plumbing has been modified multiple times over the years are all more likely to show corrosion-related staining.

Is it actually a problem?

The stain on its own isn’t dangerous. But it’s a symptom, and what it’s pointing at can become a real problem if you ignore it.

Copper corrosion that’s progressed far enough to leave visible staining is also thinning the pipe wall from the inside. Over time — sometimes years, sometimes faster depending on conditions — that leads to pinhole leaks. A pinhole leak inside a wall or under a floor is exactly the kind of slow, hidden damage that goes unnoticed until the water bill spikes or the wall starts to bubble. See our guide on how plumbers find hidden water leaks if you’re already concerned water might be moving somewhere it shouldn’t.

Electrolytic corrosion tends to be faster and more localised. If the staining is concentrated at a specific join or fitting rather than spread across multiple fixtures, that’s worth getting checked sooner rather than later.

Where the staining shows up, and what it tells you

The location of the stain gives you useful information:

  • Around the base of taps and mixers: Usually indicates corrosion in the tap body itself, the flexible hoses beneath, or the copper supply lines feeding the fixture.
  • Inside the basin or sink bowl, near the drain: Water is sitting and evaporating in the same spot repeatedly. The copper is coming from somewhere upstream — often the tap or the supply pipe to it.
  • Around the toilet inlet valve or inside the cistern: The fill valve or the brass fittings inside the cistern may be corroding. Cistern water sits still for long periods, which accelerates the reaction.
  • On the showerhead or around the shower rose: The brass or copper components in the showerhead itself, or in the arm fitting in the wall, are the likely source.
  • At multiple fixtures across the house: Widespread staining at several different locations suggests a systemic issue — possibly older copper pipework throughout the home that’s reaching the end of its reliable life.

Older Sydney homes: why this comes up more often

Copper pipes were the standard supply line material in Sydney homes from roughly the 1960s through to the 1990s. A well-installed copper system in good conditions can last 50 years or more. But copper that’s been in service for 40-plus years, in a home that’s been repaired and extended multiple times, with a mix of metals in the system, is more likely to show signs of corrosion.

If your home was built before the mid-1980s and you’re seeing blue-green staining at more than one fixture, it’s worth having a plumber look at the broader condition of your supply lines — not just the individual tap or fitting where the stain is visible. Our article on galvanised pipes in older Sydney homes covers the related question of when ageing supply pipes need to be replaced rather than patched.

What you can check yourself

Before calling anyone, a few quick checks are worth doing:

  • Is the staining at one fixture or several? One fixture suggests a localised issue with that tap, fitting, or the supply line directly behind it. Multiple fixtures suggest something more systemic.
  • Is it only in the toilet? If you use coloured cistern tablets or in-cistern cleaners, rule those out first.
  • Does it look fluffy or surface-grown? If so, it may be mould rather than copper residue — check ventilation in that room.
  • Check the flexible hoses under the sink. Pull open the vanity cabinet and look at the braided hoses connecting the tap to the supply lines. If you can see green or blue residue at the connection points, or if the hoses look bulging, discoloured, or older than 10 years, flag those for replacement regardless.

When to call a plumber

Call a plumber if:

  • The staining is appearing at multiple fixtures and getting worse over time
  • You can see corrosion or green crusting at pipe joints, not just at the fixture surface
  • The staining has appeared suddenly after a repair, pipe disturbance, or renovation — this can indicate dissimilar metals have been joined incorrectly
  • You’re also noticing a metallic taste in the water, a drop in water pressure, or brown water from the hot tap — these suggest the corrosion is more advanced
  • The flexible hoses under your sinks haven’t been replaced in 10 or more years

A licensed plumber can identify the source of the corrosion, check the condition of the supply lines, and advise whether you’re looking at a simple fitting replacement or something that warrants a closer look at the pipework. If there’s any concern about hidden damage, pressure testing or a visual inspection of accessible pipe runs can give you a clear picture before anything becomes urgent.

Jasco Plumbing works across Sydney and can assess the condition of your taps, fittings, and supply lines on the same day. If you’re seeing blue-green staining and want to know what’s actually behind it, call us or book a visit online.

GOT A PROBLEM? WE'VE GOT A PLUMBER.

Give us a call or book online. We're across the whole Sydney Region, 7 days a week – ready when you need us.