TL;DR
- The toilet is the single biggest water user in most Sydney homes, accounting for a large share of total indoor use. Showers are a close second.
- Together, toilets and showers can account for more than half of everything your household uses indoors.
- Old fixtures make the gap worse. An ageing single-flush toilet, a pre-WELS showerhead, and a dripping tap can add tens of thousands of litres to your annual bill without anyone noticing.
- The good news: fixing or upgrading the right fixtures makes a measurable difference. You don’t need to overhaul the whole house — just know which ones to prioritise.
Start with the number everyone forgets
Sydney Water puts average per-person daily water use at around 200 litres. For a household of four, that’s roughly 800 litres a day flowing through your pipes. The question most people never ask is: where does it actually go?
The answer matters because not all fixtures are equal. Some run for seconds. Others run for minutes, multiple times a day, by every person in the house. Getting clear on which fixtures are doing the most work tells you exactly where to focus if your water bill looks high or you’re trying to use less.
Here’s how it breaks down, fixture by fixture, from the thirstiest to the least.
1. The toilet: the biggest water user in most homes
It’s not the shower. It’s the toilet.
Toilets account for a significant share of all indoor water use — estimates consistently put it at roughly 30 to 40 percent of a household’s total indoor consumption. The reason is simple: it gets used multiple times a day, by every person in the house, and each flush moves a fixed volume of water regardless of what went in.
The numbers depend entirely on the age of the toilet:
- Old single-flush toilets (common in Sydney homes built before the 1990s) use anywhere from 11 to 18 litres per flush. Some older models use even more.
- Modern dual-flush toilets rated at 4 stars under the WELS scheme use 4.5 litres on full flush and 3 litres on half flush.
That gap is significant. At five flushes per person per day, an old single-flush toilet in a home of four people could be using 220 to 360 litres a day just from flushing. A modern dual-flush setup cuts that by more than half.
And that’s before you factor in a running toilet. A cistern that’s leaking silently — not overflowing, just weeping past a worn flapper — can waste up to 260 litres a day without anyone noticing a drip. If that sounds familiar, our guide on how much water a running toilet wastes covers the numbers in detail.
What to do: if your toilet is a single-flush model or was installed before 2000, it’s worth getting it assessed. A licensed plumber can confirm whether a replacement makes sense for your household.
2. The shower: second highest, but very fixable
Showers typically account for around 17 to 30 percent of indoor water use, depending on the household and the showerhead. The flow rate of the showerhead is the key variable — and it’s where the gap between old and new fixtures is most dramatic.
Here’s what the data shows:
- Older showerheads (pre-WELS era) can use 15 to 25 litres per minute.
- A modern 4-star WELS rated showerhead uses 6 to 7 litres per minute.
- The minimum standard for new installations in NSW is now 3 stars, which caps flow at 9 litres per minute.
For a household where two people each take a 7-minute shower daily, the difference between an old showerhead and a 4-star model can be more than 9,000 litres per person per year. Multiply that across a full household and it’s a substantial saving.
One thing worth knowing: swapping a showerhead in NSW is one of the few plumbing jobs you can legally do yourself, provided you’re replacing like-for-like and not altering any pipework. If you’re not sure what’s involved, or if your water pressure is already low, read our breakdown of water-saving showerheads and what they actually do to pressure before buying anything.
3. Taps: low per-minute use, but they add up
Taps don’t get the same attention as toilets and showers, but they’re running multiple times a day across every sink in the house — kitchen, bathroom, laundry.
Standard taps without aerators can discharge 15 to 18 litres per minute. Low-flow aerating taps can bring that down to as little as 2 litres per minute, with no noticeable difference in how the water feels for hand washing or rinsing.
The bigger issue with taps isn’t the flow rate — it’s leaks. A tap dripping one drop per second can waste up to 200 litres a day. That’s roughly 73,000 litres a year from a single dripping tap that most people put off fixing because it seems minor. It isn’t. The longer it drips, the worse the internal wear gets, and the more expensive the eventual repair. Our post on what happens when you put off a leaking tap repair explains exactly how the costs compound.
For the taps themselves, aerators are a cheap, easy upgrade. A licensed plumber can fit them across your whole house in a single visit.
4. The washing machine: high volume, but manageable
Laundry accounts for roughly 15 to 20 percent of household water use. A top-loader washing machine — still common in older Sydney homes — uses significantly more water per load than a front-loader of equivalent capacity.
An older top-loader can use 150 litres or more per wash cycle. A modern 4-star WELS-rated front-loader uses roughly a third of that. The WELS scheme covers washing machines, and the star rating is displayed on the label when you buy — more stars means less water per kilogram of laundry.
From a plumbing standpoint, the main thing to check is the inlet hoses behind the machine. Braided flexible hoses on washing machines are a known failure point, especially once they’re more than 10 years old. A split hose at mains pressure is one of the most damaging household water events there is — not because of the washing machine itself, but because of the volume of water it can release before anyone finds the tap. If yours haven’t been checked recently, it’s worth adding them to the list next time a plumber visits.
5. The dishwasher: more efficient than most people think
The dishwasher is often blamed for high water use, but it’s actually one of the more efficient fixtures in a modern home. A typical dishwasher uses around 12 to 15 litres per cycle. Washing the same load by hand under a running tap uses considerably more.
The main thing that affects dishwasher water use is how you run it: full loads use the same water as half loads on most settings, so running it half-empty doubles the per-item water cost. That’s a habit issue, not a plumbing one.
From a plumbing perspective, the connections are what matter. A loose or ageing water supply line under the dishwasher can leak slowly without being obvious until there’s cabinet damage or a water stain on the floor. If your dishwasher is more than 10 years old and the supply line hasn’t been looked at, it’s worth a check.
6. The bath: high per-use volume, low frequency
A standard bath holds around 150 to 200 litres when full. That’s a lot of water in one go — but most households don’t use the bath daily, which keeps the overall contribution to total use lower than the toilet or shower.
For households with young children who bath every night, the cumulative volume is worth thinking about. A half-filled bath for a small child uses far less than a full adult bath, and the habit of reusing bath water on the garden is an easy way to offset some of the volume.
There’s no WELS rating on baths because the volume is determined by how full you fill it, not by the fixture itself. The tapware filling the bath does have a WELS rating, which affects how fast it fills and how much water is used while the temperature is being adjusted.
The fixture that doesn’t get counted: hidden leaks
Hidden leaks don’t appear in any fixture breakdown because they’re not a fixture — they’re a fault. But they belong in this conversation because they can quietly add tens of thousands of litres to your annual use without any single tap, toilet, or shower being the obvious culprit.
Signs worth paying attention to:
- Your water bill has climbed and nothing obvious has changed
- You can hear water running when every tap and appliance is off
- There are damp patches on walls, floors, or ceilings with no clear source
- Your water meter is ticking when the house is empty
A licensed plumber can run a meter test and, if needed, use acoustic leak detection or thermal imaging to find where the water is going. Catching a hidden leak early is almost always cheaper than finding it after it’s done structural damage.
Quick reference: fixture water use at a glance
| Fixture | Typical use (older model) | Typical use (WELS-rated) |
|---|---|---|
| Toilet (per flush) | 11–18 litres | 3–4.5 litres (dual flush) |
| Shower (per minute) | 15–25 litres/min | 6–9 litres/min |
| Tap (per minute) | 15–18 litres/min | 2–6 litres/min (with aerator) |
| Washing machine (per load) | 120–200 litres | 40–80 litres |
| Dishwasher (per cycle) | 15–20 litres | 9–13 litres |
| Bath (full) | 150–200 litres | Depends on fill level |
| Dripping tap (per day) | Up to 200 litres | Zero (fixed) |
| Running toilet (per day) | Up to 260 litres | Zero (fixed) |
Where to start if your bill looks high
You don’t need to upgrade everything at once. The highest-impact changes, in order, are:
- Fix any leaks first. A running toilet or dripping tap is costing you money every day. Get those sorted before anything else.
- Check the toilet. If it’s a single-flush model or more than 20 years old, a modern dual-flush replacement pays for itself over time.
- Swap the showerhead. A 4-star WELS showerhead is one of the cheapest upgrades with one of the fastest paybacks.
- Fit aerators on taps. Quick, inexpensive, and barely noticeable in use.
- Check flexible hoses. Not a water-saving measure, but a damage-prevention one. Braided hoses on washing machines, dishwashers, and under sinks should be inspected every 5 to 10 years.
If you’re not sure where your household’s water is going, the Sydney Water water use and conservation page has a usage calculator that gives a rough breakdown by fixture type.
For anything beyond a showerhead swap or aerator fit — toilet replacement, leak detection, washing machine hose checks, or a full fixture audit — you need a licensed plumber. In NSW, most plumbing work beyond basic maintenance must be done by someone holding a current NSW licence. You can check any plumber’s licence number on the NSW Fair Trading register before booking.
The WELS scheme also has a product search tool on the Australian Government energy and water efficiency page if you want to compare specific fixtures before buying.
Ready to find out where your water’s going?
If your Sydney Water bill has been creeping up and you can’t point to an obvious reason, the most useful first step is a plumber walking through your fixtures and checking for faults. We do that as part of a standard visit — no guesswork, no upsell, just a straight answer on what’s using water and what’s worth fixing.
Call us or book online and one of us will come out and take a look.