TL;DR
- A dripping tap doesn’t stay a dripping tap. The fault that caused it is getting worse every day, and the longer you wait, the more expensive and disruptive the repair becomes.
- According to Sydney Water, a tap dripping one drop per second wastes around 7,000 litres a year. A faster drip or a hot water tap pushes that number, and your bills, much higher.
- The real urgency isn’t the water bill. It’s the secondary damage: corroded valve seats, rotting cabinetry, mould behind walls, and a repair that escalates from a $150 washer swap to a full tap replacement or worse.
- In NSW, most tap repair work requires a licensed plumber. Getting it sorted early means a shorter visit, a smaller bill, and no nasty surprises behind the handle.
A drip is a symptom, not the problem
That steady drip from the kitchen tap isn’t just water finding its way past a seal. It’s telling you something has worn out or failed inside the mechanism. In older washer-style taps, it’s usually a rubber washer that’s compressed flat or split. In modern mixers, it’s typically a ceramic cartridge that’s cracked or lost alignment.
Either way, the underlying fault doesn’t pause while you think about it. Water under pressure keeps working against the damaged part, grinding the seat, widening the gap, and turning a simple component swap into a bigger job.
The timeline most people don’t see
Here’s roughly what happens when a dripping tap gets left alone. Every home is different, but this pattern shows up on job after job.
Week one to two: just a drip
The washer or cartridge has started to fail. Water gets past the seal when the tap is off. You hear it at night. It’s annoying, but the tap still works fine when you use it. At this stage, the fix is usually quick: a washer replacement or cartridge swap, done in under an hour.
Week three to six: the drip speeds up
Water flowing past a damaged seal erodes the valve seat, the brass surface the washer presses against. Once that seat is scored or pitted, a new washer alone won’t seal properly. Now the plumber needs to regrind or recut the seat before fitting the washer, which adds time and cost to the job.
Month two to three: moisture starts doing damage
Constant dripping saturates the area around the tap. Under a kitchen sink, that means a particleboard cabinet base soaking up water and starting to swell. Around a bathroom basin, water tracks along the vanity top, under the silicone line, and into the cupboard below. Mould starts forming in spots you can’t see without pulling things out.
Month three and beyond: the repair bill grows
By now, the valve seat may be too damaged to regrind. The tap body itself can start corroding, especially in older brass fittings where years of mineral deposits have already weakened the metal. What started as a parts swap becomes a full tap replacement, sometimes with cabinet repairs or mould remediation on top.
Hot water taps cost you twice
If the drip is on a hot water line, you’re paying for the water and the energy to heat it. Your hot water system doesn’t know the difference between a shower and a leak. It just keeps firing to replace the lost heat. On an electric storage system running on a standard tariff, that background energy cost adds up quietly every quarter.
The water waste is real, not theoretical
Sydney Water’s own published data puts the number clearly: “a dripping tap can waste up to 2,000 litres of water a month.” That’s up to 24,000 litres a year from a single tap. Two dripping taps in the same house, one in the kitchen and one in the bathroom, and you’re looking at a meaningful jump in your quarterly bill for water you never actually used.
The damage you don’t notice until it’s expensive
The water bill gets the attention, but the hidden damage is where the real cost sits.
- Swollen or delaminating cabinetry. Particleboard under sinks absorbs water quickly. Once it swells, it doesn’t go back. Replacing a vanity cabinet costs far more than fixing the tap that caused it.
- Mould in enclosed spaces. The cupboard under a dripping tap is warm, dark, and damp. That’s textbook conditions for mould growth, and once it’s established in the back of a cabinet or behind a splashback, it’s not a wipe-down fix.
- Staining and corrosion. Persistent drips leave mineral stains on basins and sinks. Worse, water sitting around the base of a tap corrodes the mounting hardware and can damage the benchtop underneath.
- Insurance complications. Most home insurance policies cover sudden water damage, like a burst pipe, but not gradual damage from a leak you knew about and didn’t fix. A dripping tap you’ve been ignoring for months falls squarely into the gradual category.
Units and apartments: it’s not just your problem
In a unit or apartment, a leaking tap in your kitchen or bathroom can send water into the unit below. That turns your deferred maintenance into someone else’s ceiling stain, and potentially a strata dispute. If the leak causes damage to common property or a neighbour’s lot, you may be liable for the repair costs, especially if it’s clear the fault was left unattended.
Why the repair gets harder the longer you wait
Plumbers see this pattern constantly. A tap that would have taken 30 minutes to fix in week one becomes a two-hour job three months later because the seat is chewed up, the spindle is seized, or the body of the tap has corroded around the cartridge housing. In older Sydney homes with original brass tapware, corrosion can make it impossible to remove the old cartridge without damaging the tap body. At that point, you’re replacing the entire tap, not just the internals.
There’s also a compounding effect. A tap that drips slowly puts constant low-level stress on the plumbing behind it. Flexible hoses under the sink stay slightly pressurised, isolation valves that haven’t been turned in years get mineral buildup around the spindle, and fittings that were fine last year start weeping at the joints.
What you’re allowed to do yourself in NSW
Not much, when it comes to tap repairs. Under NSW law, replacing washers, cartridges, or any component connected to the water supply is classified as plumbing work and must be done by a licensed plumber. You can tighten a loose aerator (the small filter screen at the tip of the spout) or clean a clogged aerator, but anything that involves removing tap components or touching supply lines needs a licence.
That’s not red tape for the sake of it. Incorrect tap repairs can make the leak worse, damage the valve seat, or leave fittings that fail under pressure later. A licensed plumber carries the insurance and provides the compliance sign-off that protects you if something goes wrong down the track.
The five signs your drip has already escalated
- The drip rate has increased since you first noticed it. That means the seal is deteriorating further.
- The tap handle feels different. Stiffer, looser, or grinding when you turn it. The internals are wearing.
- There’s moisture under the sink that wasn’t there before. Water is tracking somewhere it shouldn’t.
- You can see green or white mineral deposits around the base of the tap or on the fittings below. That’s long-term water exposure.
- The drip continues even when you crank the tap hard. The seat is damaged and extra force won’t fix it.
If any of those sound familiar, the tap is past the “I’ll get to it” stage.
A quick repair now vs a bigger job later
Most leaking tap repairs are straightforward when they’re caught early. A plumber arrives, isolates the water, pulls the tap apart, swaps the worn component, checks the seat, reassembles, and tests. For a standard washer or cartridge replacement, the whole visit is often under an hour.
Wait a few months and that same job can involve regrinding the seat, sourcing a replacement cartridge for an older mixer, dealing with seized components, and sometimes replacing the tap entirely. The difference between “caught it early” and “left it too long” is real, and it shows up on the invoice.
If you’re wondering whether your tap can be repaired without replacing the whole unit, we’ve covered that in detail: fixing a leaking tap without replacing it.
The honest takeaway
A dripping tap is one of the easiest plumbing problems to fix and one of the most expensive to ignore. Every week you put it off, the fault gets a little worse, the repair gets a little bigger, and the secondary damage creeps a little further into your cabinetry, your bills, and potentially your neighbour’s ceiling.
If you’ve got a tap that won’t stop dripping, the smartest move is the simplest one: get it looked at now, before the seat is damaged, the cabinet is wet, or the repair turns into a replacement.