Most people don’t care much about brand names until the old tank rusts out and someone has to fit a new one against the side of the house by lunchtime. Then the questions get very specific. Will it fit where the old one sat? Does the gas line need work? Who signs off on it? And will the warranty actually hold up if something goes wrong in year six?
Rheem is what we fit most often across Sydney, mainly because the range covers almost every situation we walk into, and parts are easy to get when a unit needs service later. Here’s how a Rheem install actually runs when we do it.
TL;DR
- We start by matching the Rheem model to your existing setup: gas storage, gas continuous flow, electric storage, heat pump or solar. A straight swap is the fastest and cheapest path, and changing type takes more work.
- A typical like-for-like Rheem changeover is usually a half-day job. Changing fuel type, moving the unit, or adding a heat pump takes longer and can involve an electrician.
- Gas work is done by a licensed gas fitter, full stop. Electrical connection for hardwired units is done by a licensed electrician.
- Temperature control matters. New installs need to deliver no more than 50°C to bathroom outlets, which means a tempering valve or a factory 50°C preset Rheem model.
- Rheem’s cylinder and heat exchanger warranties only hold if the unit is installed to the manufacturer’s instructions by a licensed person. Bad installs void good warranties.
- You get a fixed price before we start, and the work carries our lifetime workmanship warranty.
Step one: working out which Rheem you actually need
Nine times out of ten this decision is already half-made by what’s sitting there now. Gas storage on the side of the house, electric tank in the laundry cupboard, continuous flow unit on an apartment balcony wall. Staying with the same fuel and the same style keeps the pipework, the flue and the electrical side simple.
Where it gets more interesting is when your household has changed. Two people in a townhouse have very different needs to a family of five with two bathrooms and a teenager who treats the shower like a spa.
Rough guide to how we match a Rheem model to a home:
- Gas storage (90L, 135L, 170L and up): good for homes that want strong mains-pressure hot water to several taps at once, with a decent recovery rate so you’re back in hot water quickly after a big run.
- Gas continuous flow (12L to 28L per minute): wall-mounted, compact, and heats only when you turn the tap on. The litres-per-minute rating is the thing that matters, not tank size. A 20L unit suits most family homes, and the bigger 28L unit handles up to three bathrooms. Two units can also be linked to act as one where demand is very high.
- Heat pump (Rheem AmbiPower and MPi series): electric, but far more efficient than a standard element because it pulls heat from the air. Sizes around 180L to 325L cover small households through to larger families. Needs outdoor air space and a spot where a bit of fan noise won’t bother anyone.
- Electric storage: still the simplest swap in units and older homes with no gas, and sometimes the only practical option in tight indoor cupboards.
- Solar: worth a conversation if your roof suits it. We’ve covered the buying side of that in our guide to buying a solar hot water system in Sydney.
If you’re still weighing up categories rather than models, our plain-English rundown of the types of hot water systems is the better place to start.
Step two: the site check that stops surprises
Before anything gets ordered, someone looks at the actual spot. Photos over the phone help for a rough idea, but the site check is where the real detail comes out.
What we’re checking:
- Clearances around the unit, especially flue and combustion clearances on gas models, and distance to windows, eaves, boundaries and anything that could catch heat.
- Whether the existing gas line and meter can supply the unit you want. A continuous flow unit pulls hard on gas, and an undersized line means weak performance no matter how good the heater is.
- The condition of the water connections, isolation valves, relief lines and the drain point.
- Where the safe tray or overflow goes on an indoor install, because indoor tanks in cupboards need somewhere for water to go.
- For heat pumps: airflow, noise to neighbours, and a proper condensate drain path.
- Access. Getting a 170L tank down a narrow side path or up to a first-floor laundry changes the job.
Then you get a fixed price for the whole job before we touch anything. No hourly meter ticking while we work out the tricky bits.
Step three: install day, start to finish
A straight Rheem-for-Rheem changeover in an accessible spot usually runs about three to five hours. Here’s the shape of it.
Isolating and removing the old unit
Water and energy supply get shut off and isolated first. Gas is capped by a licensed gas fitter. Electrical disconnection on hardwired units is handled by a licensed electrician. The old tank is drained down, disconnected and carried out, and we take it with us rather than leaving it on your nature strip.
Preparing the spot
Old bases are often cracked, sunken or the wrong size for the new unit’s footprint. Wall brackets on continuous flow and heat pump installs need to hit solid structure, not just render. This part gets skipped on rushed jobs, and it’s the reason some units sit slightly out of level and never drain properly.
Connecting water, gas or power
New tempered copper connections, isolation valve, non-return and relief lines run to spec and to the Rheem installation instructions for that model. Gas connections and pressure testing are done by the licensed gas fitter on the job. Electrical connection is left to the licensed electrician. That split isn’t us passing the buck, it’s how the licensing works in NSW.
Getting temperature control right
New installations need to deliver hot water no hotter than 50°C to bathroom outlets. In practice that means either a tempering valve fitted on the outlet, or one of Rheem’s factory 50°C preset models where a separate tempering valve isn’t required for domestic use. Both are valid. What isn’t valid is an unregulated 60°C plus feed straight to a bathroom tap, which is a genuine scald risk with kids and older family members in the house.
Commissioning and testing
Fill, purge the air, check for leaks under pressure, fire the unit, verify gas pressure where relevant, check delivery temperature at the outlets, and confirm the controller or thermostat is set correctly. On continuous flow units we run multiple taps to check the unit holds a steady temperature rather than surging hot and cold.
Handover and paperwork
We walk you through where the isolation valve is, how the controller works, how to reset the unit safely if it ever locks out, and what maintenance the model needs. You get the compliance paperwork for the work performed and the manufacturer documentation for warranty purposes. Then the area gets cleaned up and the old unit goes on the truck.
The install details that decide whether your warranty is worth anything
Rheem publishes warranty periods by model, and they’re substantial. A number of gas storage cylinders carry a ten year cylinder warranty, several continuous flow units carry twelve to fifteen years on the heat exchanger, and the AmbiPower heat pumps carry a cylinder warranty of their own. Check the current terms for your specific model, because they vary and they change.
The catch is the same across every brand: the warranty depends on the unit being installed to the manufacturer’s instructions by an appropriately licensed person, and used within the conditions it was designed for. Fitted with the wrong clearances, no tempering valve, no relief drain, or in water conditions the model isn’t rated for, and you can end up arguing about a claim seven years later. That’s a bad day for everyone.
So the boring parts of the install, the valve that costs very little and the clearance nobody sees, are the parts that protect the expensive bit.
When it’s not a simple swap
Some jobs are bigger, and it’s better to know upfront:
- Electric tank to heat pump: the new unit usually goes outside rather than in the old cupboard, so you’re looking at relocated water lines, a condensate drain, and electrical work.
- Gas storage to continuous flow: the tank footprint disappears, but the gas line often needs upsizing and the flue and clearance rules are different.
- Anything in a unit or apartment: balcony and cupboard installs come with strata rules, tight clearances and limited flue options. Worth checking with strata before you commit to a model.
- Relocating the unit: new pipe runs, new drain, and sometimes new gas or power. Adds a good chunk of time.
- Heat pumps and solar: these can be eligible for small-scale technology certificates, and eligibility depends on the model and location. Ask us what applies to the system you’re considering rather than assuming a figure you saw in an ad.
What we need from you before install day
- Clear access to the unit and the path to it. Move the bins, the bikes and the pot plants.
- Somewhere for a vehicle close enough to carry a tank in and the old one out.
- Pets secured, especially if a side gate needs to stay open.
- Strata approval sorted if you’re in a unit.
- A heads-up if anyone in the house needs hot water at a particular time, so we can plan the outage window.
Expect the hot water to be off for most of the working day. Cold water usually only goes off briefly while we isolate and reconnect.
Repair first, or replace?
We’re not going to sell you a new Rheem if the old one has a cheap fixable fault and a few good years left. A dead thermostat or element on a seven year old tank is a repair. A leaking cylinder on a fifteen year old unit is a replacement, no matter what anyone tells you. If you’re not sure which side of that line you’re on, our guide to how often to replace a hot water system lays out the realistic lifespans, and the piece on reading hot water symptoms helps you describe the fault properly when you call.
Next step
If your hot water is on its last legs, or it’s already gone and you want it sorted today, tell us what you’ve got: brand, rough age, fuel type, and where the unit sits. A photo of the data plate helps more than anything else, because it tells us the model and capacity in one shot.
From there we can confirm which Rheem suits the house, whether it’s a straight swap or a bigger job, and give you a fixed price before any work starts. All work is done by licensed plumbers (NSW licence #488187C), gas work by a licensed gas fitter, and it’s backed by our lifetime workmanship warranty. See our hot water systems page for what’s covered, or the gas fitting page if your job involves gas line work. No hot water right now and it can’t wait? That’s what our emergency plumber service is for.
You can check the full Rheem residential range at rheem.com.au, and verify any NSW plumber’s licence through NSW Fair Trading before you let them start work. We’d rather you checked.