Your old system’s on the way out, or you’re building and someone’s asked which unit you want. Suddenly you’re staring at words like storage, continuous flow, heat pump and off-peak, and none of it tells you what’s actually right for your house. Fair enough. The label on the box doesn’t explain how it’ll behave when three people want a shower before work.
This is a plain-English rundown of the main types of hot water systems you’ll come across in a Sydney home, how they differ, and which tends to suit which situation. No sales spin, just the trade-offs.
TL;DR
- Hot water systems split two ways: by energy source (electric, gas, heat pump, solar) and by how they deliver (storage tank or continuous flow).
- Gas continuous flow is the most common pick for gas-connected St George and Shire homes. Endless hot water, small wall unit, heats only what you use.
- Electric storage is cheap to buy but pricey to run unless it’s on an off-peak (controlled load) tariff.
- Heat pumps cost more upfront but run cheaper, and NSW has an incentive that lowers the install cost when you switch from electric or gas.
- Solar works well in Sydney sun but needs roof space and a booster for cloudy runs.
- Size matters more than headcount. It comes down to how many outlets run at once during your morning or evening peak.
First split: how the water gets heated
Every system runs on one of four energy sources. This is usually the decision that’s already half-made for you, because it depends on what your house is connected to.
Electric
An element heats the water, much like a big kettle. Electric systems are the cheapest to buy and the simplest to install, which is why so many older homes have one. The catch is running cost. Heating water with grid electricity at standard rates adds up, and hot water is one of the biggest chunks of a household power bill.
The way to make electric work is a controlled-load (off-peak) tariff, where the tank heats overnight on a cheaper rate. That’s a real saving, but not every home has off-peak available, and you’ll usually need a bigger tank so the overnight heat lasts all day.
Gas
If you’ve got natural gas at the property, a gas system is often the sensible middle ground. Gas heats fast, the rate doesn’t jump around during the day like peak electricity, and recovery is quick so you’re less likely to run out. It’s a licensed job to fit or move, so it’s not a DIY swap. Homes on LPG bottles instead of mains gas tend to pay more to run it.
Heat pump
A heat pump is technically electric, but instead of using an element it pulls warmth from the outside air, like an air conditioner working in reverse. That makes it far more efficient than a standard electric unit, so running costs drop noticeably. The downsides: it costs more to buy, it needs a well-ventilated outdoor spot, and the compressor makes a hum, so placement near a bedroom window or a neighbour’s wall needs thought.
Heat pumps are where the government incentives sit. The NSW hot water upgrade incentive can knock money off the install when you swap an electric or gas heater for an eligible heat pump, applied upfront in your quote. Eligibility depends on your situation and the model, so it’s worth asking about when you get quotes rather than assuming.
Solar
Solar hot water uses roof-mounted collectors (the black tubes you sometimes see) to heat water from the sun, with a gas or electric booster for cloudy stretches and heavy-use days. Sydney gets plenty of sun, so running costs can be very low. The trade-offs are a higher upfront cost, the install is more involved, and it eats roof space you might rather give to solar panels. Worth weighing if you’re already thinking about the roof.
Second split: storage tank or continuous flow
Once you’ve settled the energy source, the next question is how the system delivers the water. This is the part that most affects day-to-day life in the house.
Storage tank
A tank heats a fixed volume of water (commonly 125 to 400 litres) and keeps it hot until you use it. Simple, works at any tap at once, and no minimum flow to fire it up. The limit is capacity: once a big family drains the tank on back-to-back showers, the next person gets lukewarm water until it reheats. There’s also some standby heat loss keeping the tank warm around the clock. Storage suits off-peak electric, solar, and smaller households well.
Continuous flow (instantaneous)
Continuous flow units heat water as it passes through, only when you need it, with no tank. That means effectively unlimited hot water and a small wall-mounted unit that saves space. It’s usually gas, because whole-house electric continuous flow tends to need three-phase power that most homes don’t have. Two things to know: there’s a short delay before the hot reaches a far tap, and there’s a minimum flow rate (roughly 1.5 to 2 litres a minute) needed to trigger it, which can annoy a trickling tap.
Quick comparison
| Factor | Storage tank | Continuous flow |
|---|---|---|
| Supply | Fixed capacity, can run out | Effectively unlimited |
| Space | Floor or wall space for tank | Small wall unit |
| Standby loss | Yes, keeps water warm all day | No, heats on demand |
| Minimum flow | None | Needs a minimum flow to fire |
| Best suited to | Off-peak electric, solar, smaller homes | Gas-connected homes, most family sizes |
Which type suits your household?
Here’s the honest bit most spec sheets skip: the right size is driven by how many outlets run at the same time during your peak window, not just how many people live there. Two four-person homes can need very different systems if one has back-to-back morning showers and the other spreads its use out.
As a rough guide for Sydney homes:
- 1 to 2 people, apartment or low demand: a smaller storage tank or a lower-output continuous flow unit usually copes.
- 3 to 4 people, one bathroom: a mid-range storage tank or a moderate continuous flow unit. Watch the morning overlap.
- 4+ people or two bathrooms with overlap: a larger tank or a higher-output continuous flow unit sized to run more than one shower at once.
If you’re in an older St George house with a single bathroom, a like-for-like tank swap is often the easy answer. Move up to a busier household or a two-bathroom home in the Shire, and getting the flow rate right matters more than the brand on the front.
A word on doing it yourself
Choosing the system is fair game. Fitting it isn’t. Hot water installs involve regulated plumbing, and gas units also involve gas work, both of which have to be done by a licensed plumber or gas fitter in NSW. There’s tempering valve setup, pressure relief, correct venting for gas, and safe disposal of the old unit to sort out. Getting any of that wrong is a scald or safety risk, not just a warranty problem. So pick the type, then leave the connection to someone licensed.
Repair, or time to replace?
If your current system is just playing up rather than dead, you might not need any of this yet. Plenty of no-hot-water faults come down to a tripped switch, a pilot light, or a worn part. It’s worth ruling those out first. Our guide on why a hot water system stops working walks through the safe checks and the warning signs that mean it’s replacement time.
The bottom line
Start with what your home is connected to, then decide between the endless supply of continuous flow and the simplicity of a storage tank, and size it to your busiest hour rather than your headcount. If gas is available, continuous flow is the common winner around here. If you’re chasing lower running costs long term, a heat pump is worth pricing with the NSW incentive factored in.
Not sure which way to go for your place? Tell us what you’ve got now and how many people use it, and we’ll give you an honest recommendation and a fixed-price quote before any work starts. Have a look at our hot water systems service, or get in touch and one of the team will call you back. Gas swap on the cards? Our licensed gas fitting covers that side too.