Leaking Bathroom Tap: Diagnose It, Fix What You Can, Know When to Call

Plumbing Tips

TL;DR

  • Where the water appears tells you which part has failed — spout drip, handle leak, and base leak are three different problems.
  • Bathroom taps come in three main types: traditional washer taps (multi-turn), ceramic quarter-turn taps, and single-lever mixer taps. The fix depends entirely on the type.
  • In NSW, replacing a washer or O-ring is generally considered legal DIY. Anything involving the supply lines, isolation valves, or the tap body itself is licensed work.
  • If the drip comes back within a few weeks of a new washer, the valve seat is worn — that needs a plumber, not another washer.
  • Jasco fixes leaking bathroom taps across Sydney with a fixed price before work starts and no callout fee for new customers.

Start by watching where the water actually comes from

Before you touch anything, spend thirty seconds watching the tap. The location of the drip is the most useful clue you have — and getting it wrong means pulling the tap apart for no reason.

  • Water dripping from the spout when the tap is off: the sealing part inside the tap — washer, jumper valve, or ceramic cartridge — is no longer closing properly.
  • Water weeping around the handle or collar: the O-ring on the spindle has degraded. Common on older mixer taps and separate hot/cold basin sets.
  • Water pooling at the base of the tap or under the basin: this usually points to a connection problem — a loose flexible hose, a worn fitting, or a leaking isolation valve — not the tap itself.

Each of these is a different repair. Knowing which one you’re dealing with saves time and stops you buying parts you don’t need.

Which type of bathroom tap do you have?

The tap type determines what’s inside and what part wears out. Most Sydney bathrooms have one of three:

Traditional washer tap (multi-turn)

The handle turns several full rotations from fully off to fully on. You’ll often see these as separate hot and cold taps on older basin sets or bath surrounds. Inside is a rubber washer pressed against a brass valve seat. These taps rely on a rubber or fibre washer pressing against a valve seat to stop water flow. When the washer hardens or splits, water seeps through even with the tap fully closed.

The fix: replace the washer and jumper valve. If a new washer only lasts a few weeks, the seat itself is pitted and needs reseating.

Ceramic quarter-turn tap

The handle moves only a quarter turn from off to full flow. Unlike traditional taps, ceramic disc taps use a cartridge housing two ceramic discs instead of a rubber washer. The discs sit flush against each other and rotate to control water flow and temperature with a quarter-turn action.

Because ceramic is far harder wearing than rubber, these taps are known for lasting a long time without needing maintenance — but the discs, seals, and valve seat inside the cartridge can all wear out eventually, and that’s when the dripping starts. Grit or mineral build-up between the discs can also cause a drip without any actual wear — sometimes a clean is all it takes.

The fix: replace the cartridge as a unit. Cartridges are brand-specific, so take the old one with you when buying a replacement.

Single-lever mixer tap

One handle controls both temperature and flow. Mixer taps feature a single lever that controls both hot and cold water from a single tap mechanism. There are rubber seals and springs inside the cartridge. When the seals in the cartridge wear away or break, water leaks through the tap mechanism.

A drip from the spout means the cartridge needs replacing. Water around the base of the spout usually means the O-ring has gone. If a mixer tap drips after closing, don’t keep tightening the handle to stop it. This forces the worn ceramic discs together harder, creating deeper scratches that make the problem worse. The only proper fix is cartridge replacement.

What you can legally do yourself in NSW

NSW plumbing law is worth understanding before you pick up a spanner. The general position is this: replacing internal tap components — a washer, O-ring, or cartridge — is work a competent homeowner can do without a licence. Replacing the tap or mixer, the flexible hoses, the isolation valves, or any work on the pipework is licensed plumbing work in NSW.

In plain terms: you can open the tap, replace what’s inside, and put it back together. You cannot touch the supply lines, move the tap, or replace the tap body. If you’re not sure where that line falls on your specific job, a licensed plumber is the safer call.

Step-by-step: replacing a washer in a traditional bathroom tap

This is the most common bathroom tap repair in older Sydney homes. It covers separate hot and cold taps on a basin or bath.

What you’ll need

  • Adjustable spanner or shifting wrench
  • Flathead screwdriver
  • Replacement washer and jumper valve (buy a few sizes — they’re cheap)
  • Replacement O-ring (same diameter as the existing one)
  • Soft cloth or rag to protect the tap finish

The steps

  1. Turn off the water. Look under the basin for the isolation valve on the supply hose and turn it clockwise until it stops. If there isn’t one, or it won’t hold, turn off the water at the meter tap at your front boundary.
  2. Open the tap fully to release pressure and confirm the water is off. If water keeps flowing, the isolation valve isn’t holding — go to the meter.
  3. Plug the drain. Small screws and washers disappear down drains with depressing reliability.
  4. Remove the tap button or cap. This is the small disc on top of the handle marked “H” or “C”. Prise it off gently with a flathead screwdriver.
  5. Unscrew the handle. There’s usually a screw underneath the cap. Remove it and lift the handle off.
  6. Remove the tap bonnet. Use your spanner wrapped in a cloth to avoid scratching. Turn anti-clockwise.
  7. Lift out the spindle. At the base of the spindle is the washer, held by a small brass screw. Inspect it — if it’s flattened, cracked, or has a groove worn into it, that’s your problem.
  8. Replace the washer and check the O-ring. Fit the new washer snugly. While you’re in there, slide the O-ring off the spindle and replace it — they’re cheap and it saves doing this job again in six months.
  9. Reassemble in reverse order. Don’t overtighten the bonnet — firm is enough. Overtightening wears the new washer faster.
  10. Turn the water back on and test. Let it run for a moment, then close the tap and watch the spout. If it still drips after a minute, see the section below on valve seats.

Step-by-step: replacing a ceramic cartridge

This applies to quarter-turn taps and single-lever mixer taps — which covers most modern bathroom basins and bath mixers in Sydney homes.

  1. Turn off the water at the isolation valve under the basin or at the meter. Open the tap to release pressure.
  2. Plug the drain before removing anything.
  3. Remove the handle. Most modern taps have a decorative cap hiding a screw at the top of the handle. Pop the cap, remove the screw, and lift the handle straight off.
  4. Take a photo of the cartridge before you remove it. The orientation matters when you fit the new one.
  5. Unscrew the cartridge retaining nut (or grub screw, depending on the brand) and pull the cartridge straight out.
  6. Match the cartridge before you buy. Take the old cartridge to a plumbing supplier. Cartridges are brand and model specific — a wrong-sized one won’t seal. Note the brand name on the tap body if you can find it.
  7. Fit the new cartridge in the same orientation as the old one (that photo helps here). Tighten the retaining nut firmly but not aggressively.
  8. Reassemble the handle, turn the water back on, and test.

When a new washer doesn’t fix it: the valve seat problem

This is the repair people miss most often. You replace the washer, the drip stops for a few weeks, then it’s back. The washer isn’t the problem — the brass valve seat it presses against has become pitted or corroded.

The metal seat can become pitted by mineral deposits. If this happens, even a brand-new washer will not create a watertight seal.

Reseating the valve requires a tap reseating tool — a small, inexpensive tool that grinds the seat flat again. It’s a job a competent DIYer can do, but if you’re not comfortable with it, or if the seat is too far gone to resurface, a plumber can assess whether the seat is salvageable or whether the tap needs replacing. For more on that decision, see our guide on fixing a leaking tap without replacing it.

Where the leak is around the base of the spout or handle

If the drip is coming from around the handle collar or the base of the spout rather than the spout tip, the O-ring is usually the cause. Water around the handle may be caused by a worn O-ring, seal or cartridge. The affected part may need cleaning, tightening or replacing.

On a mixer tap, the O-ring sits around the cartridge body or the spout base. Replacing it is straightforward once the tap is disassembled — the tricky part is finding the right O-ring diameter. Take the old one with you to the hardware store.

If water is pooling under the basin rather than at the tap itself, the problem is almost certainly in the supply connections — a loose flexible hose fitting or a failing isolation valve. That’s licensed plumbing work, not a DIY tap repair.

Bathroom tap leaks in older Sydney homes

If your home was built before the 1990s, there’s a reasonable chance the bathroom taps are original or at least quite old. A few things to keep in mind:

  • Older taps may use non-standard washer sizes. Bring the old washer with you rather than guessing.
  • Galvanised supply lines on older properties can have mineral build-up that accelerates cartridge and washer wear. A recurring drip on a recently serviced tap is often a sign of pressure or water quality issues, not just bad luck with parts.
  • Isolation valves may be absent or seized. Many older bathrooms don’t have isolation valves under the basin. If yours won’t close, you’ll need to work at the meter — and if the meter tap is also seized, call a plumber before you start.
  • Tap bodies on older mixers can be corroded internally. If the spindle won’t come out cleanly or the body feels gritty, don’t force it. Cracking an old tap body mid-repair turns a minor fix into a full replacement.

If you’re dealing with recurring leaks across multiple bathroom taps in an older home, it may be worth getting the water pressure checked — high water pressure puts strain on every fitting in the house and accelerates wear on washers and cartridges.

When to stop and call a licensed plumber

Some bathroom tap leaks are straightforward DIY jobs. Others look simple but aren’t. Call a licensed plumber when:

  • The leak is coming from under the basin, not the tap itself — supply connections and isolation valves are licensed work.
  • You’ve replaced the washer twice and the drip is back — the valve seat needs professional attention.
  • The tap body is cracked, corroded, or the spindle won’t move freely.
  • You can’t find a replacement cartridge that matches your tap brand.
  • The isolation valve under the basin won’t close and the meter tap is also seized.
  • The leak is near the wall or behind the tiles — that’s a different problem entirely, and not a tap repair.

A leaking tap that gets ignored tends to get worse, not better. The water waste adds up faster than most people expect, and a drip that starts as a worn washer can quietly turn into a corroded valve seat or water damage inside the wall cavity. For a clear picture of what that actually costs over time, see what happens when you put off a leaking tap repair.

Get it sorted today

If the tap is beyond a simple washer swap, or you’d rather have it done properly in one visit, Jasco fixes leaking bathroom taps across Sydney with a fixed price before work starts. No callout fee for new customers, licensed plumbers only, and we leave the work area clean. See our leaking tap repair service or call us directly to book a same-day visit.

GOT A PROBLEM? WE'VE GOT A PLUMBER.

Give us a call or book online. We're across the whole Sydney Region, 7 days a week – ready when you need us.