Why Your Toilet Keeps Running After You Flush

Plumbing Tips

TL;DR

  • A toilet that keeps running after flushing has a problem inside the cistern, not the bowl.
  • The five most common causes are a worn flush valve seal, a faulty fill valve, a float set too high, a tangled or kinked flush chain, and limescale or debris fouling the seat.
  • The sound it makes tells you a lot: a steady hiss usually points to the fill valve; a trickle into the bowl usually means the flush valve seal.
  • Some checks are safe to do yourself. Replacing valves and internal cistern parts is licensed plumbing work in NSW.
  • Left running, a toilet can waste hundreds of litres a day and push your Sydney Water bill up significantly.

What the sound is telling you

Before you lift the lid, listen. The noise coming from the cistern narrows down the cause before you’ve touched anything.

A steady hiss that runs continuously after the cistern has filled points to the fill valve not shutting off properly. A quieter trickle, where you can hear water running into the bowl between flushes, usually means the flush valve seal at the bottom of the cistern isn’t sealing. If the cistern fills right up to the brim and keeps going, the float level is almost certainly set too high.

Those three sounds cover the majority of running toilet faults. The sections below explain each one, plus two more that come up regularly in Sydney homes.

How the cistern is supposed to work

When you press the button or handle, water stored in the cistern drops into the bowl. Once the flush is complete, the fill valve opens and refills the tank. When the water reaches the correct level, the fill valve shuts off automatically and the cistern sits quiet until the next flush.

If any part of that sequence breaks down, the cistern can’t seal properly and water keeps moving when it shouldn’t. That’s the running toilet you’re hearing.

Cause 1: A worn flush valve seal

This is the most common cause, and it’s responsible for the trickling sound you hear between flushes. The flush valve seal sits at the bottom of the cistern, directly above the opening to the bowl. Its job is to hold all that water in place until you flush.

Over time, the rubber hardens, warps, or collects a layer of sediment and limescale that stops it sitting flat. Even a small gap lets water seep through continuously into the bowl. The fill valve then keeps topping up the cistern to replace what’s leaking, so the toilet never fully stops running.

Sydney’s water supply is relatively soft compared to other Australian cities, but mineral buildup still happens, especially in older cisterns that haven’t been serviced in years.

What it sounds like: A quiet, steady trickle into the bowl. You might only notice it at night when the house is quiet.

Quick check: Put a few drops of food colouring into the cistern water without flushing. Wait ten minutes. If colour appears in the bowl, the flush valve seal is letting water through.

Cause 2: A faulty fill valve

The fill valve controls how water enters the cistern after each flush. When it works correctly, it opens as the cistern empties and closes once the water reaches the correct level. When it starts to fail, it either won’t shut off at all or keeps cycling on and off trying to maintain the level.

A fill valve can fail because of worn internal parts, debris caught in the mechanism, or simple age. Older ballcock-style valves (the kind with a horizontal arm and a ball float) are particularly prone to this as the rubber washers inside degrade.

What it sounds like: A persistent hiss or low drone that continues even after the cistern appears full. Sometimes it cycles: quiet for a minute, then hissing again.

Quick check: Lift the cistern lid and watch the fill valve after a flush. It should stop running once the water reaches the marked fill line. If it keeps going, or if you can press down on the float arm and the hissing stops, the fill valve is the likely culprit.

Cause 3: The float is set too high

Every cistern has a float, either a ball on an arm or a cylindrical float that rides up a vertical fill valve. Its job is to tell the fill valve when to stop. If the float is set too high, the cistern overfills and water spills down the overflow tube continuously, which is why you sometimes hear running water even when the flush valve seal is fine.

This can happen after a repair where the float wasn’t adjusted correctly, or gradually as the float arm bends over time. In some cases the float itself becomes waterlogged and can’t rise high enough to trigger the shutoff, which has the same effect.

What it sounds like: Water running from inside the cistern, often into the overflow pipe at the back or side. The cistern may feel permanently full when you touch the lid.

Quick check: Lift the lid and look at the water level. It should sit roughly 25mm below the top of the overflow tube. If it’s level with or above the tube, the float needs adjusting.

Cause 4: A flush chain that’s too long or tangled

This one applies mainly to older-style toilets with a flapper (a rubber disc) rather than a tower-style flush valve. The chain connects the flapper to the flush handle or button. If it’s too long, it can get caught under the flapper when it drops back down, leaving a small gap that water trickles through constantly.

It’s one of the simpler causes to check and sometimes to fix, but it still means opening the cistern and adjusting or replacing the chain, which is worth knowing before you assume it’s something more serious.

What it sounds like: Intermittent trickling into the bowl, sometimes stopping and starting as the chain shifts position.

Quick check: Lift the cistern lid and look at the chain after a flush. It should have a small amount of slack but sit clear of the flapper seal when the flapper is closed. A chain that’s coiled underneath the flapper is the problem.

Cause 5: Debris or limescale on the valve seat

Even if the flush valve seal itself is in reasonable shape, grit, sediment, or a buildup of limescale on the valve seat beneath it can prevent a proper seal. The seal can’t close flat against a surface that isn’t flat. The result is the same as a worn seal: a slow, continuous leak into the bowl.

This tends to show up in cisterns that haven’t been opened or serviced in a long time, or in older homes where the water supply pipe has some corrosion in it. A piece of debris the size of a grain of sand is enough to keep a seal from closing properly.

What it sounds like: The same quiet trickle as a worn seal. The food colouring test will confirm water is passing through, but the seal itself may look intact when you inspect it.

What you can safely check yourself

Lifting the cistern lid and looking at the parts is fine. So is the food colouring test, watching the float level, or checking whether the chain is caught. These are observations, not repairs.

Adjusting the float arm on an older ballcock valve is also something many homeowners do themselves, and it’s generally low-risk if the valve is accessible and you’re not disconnecting any supply lines.

What requires a licensed plumber in NSW is replacing internal cistern components: the fill valve, flush valve, or any part connected to the water supply. This includes inlet valves, outlet valves, and the isolation valve on the supply line. NSW plumbing law is clear that internal cistern repairs beyond basic adjustments are licensed work. Getting it wrong can result in a leak that causes water damage, or a valve that fails again quickly because it wasn’t fitted correctly.

If you’ve identified the likely cause from the checks above, that information is useful to have ready when you call. It helps the plumber arrive with the right parts and usually means the job gets done in a single visit.

The water waste is worth acting on

A running toilet isn’t just a background noise problem. A cistern leaking into the bowl can waste a significant amount of water every day, adding real dollars to your Sydney Water bill over weeks or months, often without being obvious enough to notice until the bill arrives.

The longer the fault runs, the more wear it puts on the other parts inside the cistern. A seal that started as a minor drip can eventually cause the fill valve to cycle constantly, wearing that out too. One inexpensive repair becomes two.

For a closer look at what the repair involves and what it typically costs, see our post on how to fix a running toilet.

When to call a plumber

Call us if:

  • The cistern is still running after you’ve checked the float level and chain position
  • The food colouring test confirms a leak but you can’t see an obvious cause
  • The fill valve hisses continuously even when the cistern appears full
  • The toilet is more than ten years old and has never had the internal parts serviced
  • Water is appearing around the base of the toilet or on the floor near the cistern
  • The problem came back shortly after you or someone else already adjusted something

Most running toilet repairs are straightforward. A licensed plumber can diagnose the exact cause, replace the worn part, and test the cistern in a single visit. If you’re in Sydney and want it sorted today, call Bill or one of the team at Jasco Plumbing. We’ll tell you what’s wrong before any work starts, and give you a fixed price upfront.

GOT A PROBLEM? WE'VE GOT A PLUMBER.

Give us a call or book online. We're across the whole Sydney Region, 7 days a week – ready when you need us.