TL;DR
- Gas fitting covers more than connecting a cooktop. It includes running new gas lines, extending pipework, swapping hot water systems, installing bayonet points for heaters, pressure testing, and issuing compliance certificates.
- In NSW, every piece of gas work must be done by a licensed gas fitter. A standard plumbing licence alone is not enough. The gas fitter must issue a certificate of compliance after every job.
- Most residential gas jobs take between one and four hours. The paperwork and testing at the end are not optional extras. They are legal requirements.
- If you have never had gas work done before, this article walks through what a typical visit looks like, what the fitter is actually doing at each stage, and the signs that tell you the job was done properly.
Gas fitting is not the same as general plumbing
A lot of homeowners assume any plumber can do gas work. That is not how it works in NSW. Plumbing and gas fitting are related trades, but they carry separate licence endorsements. A plumber who does not hold a gas fitting licence cannot legally touch your gas lines, connect an appliance, or sign off on the work.
This matters because gas mistakes are not forgiving. A water leak ruins a cupboard. A gas leak can cause a fire, an explosion, or carbon monoxide poisoning in an enclosed space. The licensing framework exists because the consequences of getting it wrong are serious.
If you want to understand the safety side in more detail, including what to do if you smell gas, we have covered that separately in our gas safety guide for Sydney homeowners.
The most common gas jobs in Sydney homes
Most of the gas work we see falls into a handful of categories. None of them are DIY-friendly, and all of them require a compliance certificate when they are finished.
Connecting a new gas cooktop or oven
This is probably the most frequent gas call we get. A new kitchen, a replacement cooktop, or an upgrade from electric to gas. The fitter checks the existing gas point, confirms the supply pressure suits the appliance, connects it with the correct fitting, tests for leaks, and commissions the appliance so it runs at the right flame height and gas rate.
If there is no existing gas point behind the cooktop, the job includes running a new line from the nearest supply point, which adds time and cost.
Gas hot water system install or changeover
Swapping an old gas storage tank for a new one, or switching from electric to gas continuous flow, involves gas line work on top of the plumbing. The fitter needs to confirm the gas meter and regulator can handle the new unit’s demand, connect the supply, and commission the system. If you are moving from a tank to a wall-mounted continuous flow unit, the gas line often needs to be rerouted.
We have written a separate walkthrough of what a hot water install looks like start to finish if you want the full picture.
Adding a gas bayonet point for a heater
Bayonet points let you plug in a portable gas heater without a permanent connection. The fitter runs a gas line to the wall, installs the bayonet fitting, pressure tests the new line, and checks that the room has adequate ventilation for the type of heater you plan to use. Ventilation is not a suggestion here. It is a compliance requirement.
Gas line extensions and relocations
Renovations often mean moving gas points. A kitchen that shifts to the other side of the house, a barbecue line to the new outdoor area, or a gas dryer connection in the laundry. The fitter maps the new route, runs the pipework (copper, steel, or multilayer composite depending on the location), and pressure tests the entire line before connecting anything.
Gas leak detection and repair
If you can smell gas or a pressure test shows a drop, the fitter uses leak detection fluid and electronic sniffers to find the source. Repairs might be as simple as tightening a fitting or as involved as replacing a corroded section of pipe. Either way, the line gets retested and certified before it goes back into service.
What a gas fitting visit actually looks like, step by step
If you have never had a gas fitter at your place, here is what a typical job looks like from your side of the front door.
1. The conversation before the visit
A good gas fitter asks questions before arriving. What appliance are you connecting? Is there an existing gas point? What fuel type, natural gas or LPG? Is the meter accessible? These questions help them bring the right materials and give you a realistic time estimate.
2. Site inspection
On arrival, the fitter checks the gas meter, the existing pipework, the location where the appliance will sit, and the ventilation. They are looking for anything that changes the scope: old fittings that need replacing, a meter that cannot support the new load, or a pipe run that needs rerouting.
3. A fixed price before any work starts
This is where you should get a clear, written quote. If the scope has changed from what was discussed on the phone, the fitter explains why and gives you a new number. No surprises halfway through the job.
4. The work itself
Depending on the job, this could be 30 minutes for a straightforward cooktop swap or several hours for a new line run. The fitter cuts, joins, and routes the pipework, installs isolation valves where required, and connects the appliance. Every joint is made to Australian Standard AS/NZS 5601.1, which governs gas installations nationally.
5. Pressure testing
This is not optional. Before any gas flows through the new work, the fitter pressurises the line and watches the gauge for a set period. If the pressure holds, the line is tight. If it drops, there is a leak somewhere that needs finding and fixing before the job can continue.
6. Commissioning the appliance
Once the line is proven, the fitter turns on the gas, fires up the appliance, and checks it is burning correctly. For a cooktop, that means even flame height across all burners. For a hot water unit, it means correct water temperature and proper flue operation. For a heater, it means checking the combustion and confirming ventilation is adequate.
7. The compliance certificate
Every gas job in NSW must end with a certificate of compliance. The fitter lodges this through the BCNSW eCert portal. You should receive a copy. This certificate proves the work was done by a licensed person, tested, and compliant. Keep it. You will need it if you sell the property, make an insurance claim, or have the work inspected later.
How to tell the work was done properly
You do not need to understand gas fitting to spot the signs of a job done well, or done badly. Here is what to look for after the fitter leaves.
Good signs
- You received a compliance certificate, either emailed or handed to you on the day.
- The fitter explained what they did and showed you where the new isolation valve is.
- There is no smell of gas anywhere near the new work.
- The appliance runs smoothly with a clean blue flame, not yellow or orange.
- Pipework is neatly clipped, supported, and not resting on anything that could rub or vibrate.
- The work area was left clean.
Warning signs
- No compliance certificate was issued or offered.
- The fitter did not pressure test the line, or did it so quickly you barely noticed.
- You can smell gas, even faintly, near the new connection.
- The flame on the appliance is yellow, flickering, or uneven.
- There is soot or black marks around the burner or flue.
- The fitter could not tell you their gas fitting licence number when asked.
If any of those warning signs apply, do not use the appliance. Contact another licensed gas fitter for a second opinion, and report the original work to NSW Fair Trading if no certificate was provided.
The one thing homeowners can do themselves with gas: nothing
With plumbing, there is a short list of minor jobs you are legally allowed to handle yourself in NSW, like replacing a tap washer or swapping a showerhead. Gas is different. There is no equivalent DIY list. You cannot install, alter, extend, disconnect, or repair any gas fitting or appliance yourself. Not even a small adjustment.
That includes:
- Connecting or disconnecting a gas cooktop, even if it uses a bayonet fitting.
- Moving a gas appliance to a slightly different spot.
- Replacing a gas hose or connector.
- Bleeding air from a gas line.
- Adjusting a gas regulator or valve.
The only thing you should do yourself around gas is know how to turn it off at the meter in an emergency, and call a licensed fitter for everything else.
How to check a gas fitter’s licence before they start
This takes about 60 seconds. Go to the NSW Fair Trading public register and search the licence number. It will show you the holder’s name, the licence class, and whether it is current. If the person standing in your kitchen cannot give you a licence number, that is your cue to find someone who can.
A quick reference: common gas jobs and what to expect
| Job | Typical time on site | What it involves |
|---|---|---|
| Cooktop connection (existing gas point) | 30 to 60 minutes | Connect, test, commission, certify |
| Cooktop connection (new gas line needed) | 2 to 3 hours | Run line, connect, pressure test, commission, certify |
| Gas hot water changeover (like for like) | 2 to 4 hours | Disconnect old, connect new, test gas and water, commission, certify |
| Bayonet point install | 1 to 2 hours | Run line, install fitting, test, check ventilation, certify |
| Gas leak repair | 1 to 3 hours | Locate leak, repair, retest full line, certify |
| Gas line extension (renovation) | Half day to full day | Plan route, run pipe, test, connect appliances, certify |
The honest takeaway
Gas fitting is quiet, careful work that most homeowners only think about when they are renovating or replacing an appliance. But it is also the one trade where cutting corners has the worst possible consequences. A compliant gas job means a licensed fitter, a pressure test, a properly commissioned appliance, and a certificate you can file and forget about until someone asks for it.
If you are planning any gas work at your place, or you have an appliance that is not running right, get in touch with a licensed gas fitter who will explain what is needed, quote it upfront, and leave you with the paperwork to prove it was done properly.