Water Filter Tap Installation: Plumbing Requirements in Sydney

Plumbing Tips

TL;DR

  • A dedicated water filter tap requires more plumbing work than most people expect: a new hole in the benchtop, a tee on the cold water supply line, a drain connection (for reverse osmosis systems), and a pressure limiting valve if your mains pressure exceeds 500 kPa.
  • Any work that modifies a pressurised water supply line or installs a new tap through a benchtop is licensed plumbing work in NSW. It is not legal DIY scope.
  • Every component connected to the water supply must carry WaterMark certification. Non-certified products cannot legally be installed in NSW, regardless of who does the work.
  • The install typically takes two to four hours and is done in one visit for most standard under-sink setups.
  • If you already have an existing blog post about whether you need a water filter in Sydney, this post covers the plumbing side specifically — what actually has to happen under the sink and behind the bench for a dedicated filter tap to work properly.

The part nobody mentions at the filter showroom

You’ve picked a system. Maybe it’s a twin-stage carbon filter, maybe a reverse osmosis unit. The salesperson showed you how clean the water comes out and how simple it all looks. What they probably didn’t walk you through is what a licensed plumber actually has to do to get that tap working properly in your kitchen.

There’s more to it than clipping a filter housing to the cabinet wall. The plumbing side of a dedicated water filter tap involves several distinct steps, and getting any of them wrong means leaks, pressure problems, or a system that quietly stops performing.

Here’s what the job actually involves.

First: dedicated tap or inline connection?

This is the first decision that shapes the whole job.

An inline connection routes filtered water through your existing kitchen mixer. The filter housing sits under the sink, taps into the cold supply line, and the filtered water comes out the same tap you already use. No new hole in the bench, no second tap. Simpler, but it means all the cold water through that tap runs through the filter — including water used for washing up, rinsing vegetables, and filling the kettle.

A dedicated filter tap is a separate tap, usually a small gooseneck style, installed through a new hole in your benchtop or sink deck. The filter only runs when you use that tap, which extends cartridge life and keeps the filtered supply separate. This is the more popular choice for households who want a clear distinction between drinking water and general use water.

The dedicated tap option involves more plumbing work. That’s what this article covers.

The plumbing work, step by step

1. Drilling the tap hole

A dedicated filter tap needs its own hole through the benchtop or sink deck. On a stainless steel sink, this is relatively straightforward. On stone, granite, or engineered quartz — which is common in Sydney kitchens — it requires a diamond-tipped drill bit and careful technique. Rush it or use the wrong tool and you crack a benchtop that costs several thousand dollars to replace.

This is not a job to hand to a handyman or attempt yourself. Drilling into granite or quartz benchtops is one of the most challenging installation steps and often requires a licensed tradesperson. Even on laminate or timber, the hole needs to be the right diameter and positioned so the tap body seats flush and the connections underneath have enough clearance to work.

2. Teeing off the cold water supply line

The filter system needs to connect to your cold water supply under the sink. Most systems use a saddle valve or a T-piece fitting on the cold water line. The T-piece is the better option: it creates a proper branch connection rather than a self-piercing saddle that can fail over time.

This step involves modifying a pressurised water supply fitting. If the install requires modifying any pressurised plumbing fittings or adding a new tap that breaches the bench, that work needs a licensed plumber in NSW. Any plumbing work that involves drilling through a benchtop or modifying water supply lines is covered by the NSW Plumbing Code, not DIY scope.

A plumber will also check your existing pipe material before selecting fittings. Most Sydney homes have 15mm copper pipes, but newer properties may use PEX piping, requiring specific fittings. Using the wrong fittings on PEX is a common cause of slow weeping leaks that only show up weeks later.

3. Installing a pressure limiting valve (if needed)

This is the step most DIY guides skip entirely, and it matters.

Australian standards call for a maximum water pressure of 500 kPa for plumbing installations. Having water pressure above 500 kPa may damage connected products including water filters and will void the product warranty. If water pressure exceeds 500 kPa, a WaterMark-approved pressure limiting valve must be installed at the same time as the water filter system.

Sydney mains pressure varies across suburbs and can spike above this threshold, particularly in areas with older infrastructure or properties at the bottom of a hill. A plumber will check your incoming pressure before the filter goes in. If a pressure limiting valve (PLV) is needed, it gets installed on the supply line before the filter. Skip this step and you risk damaging the filter housing, voiding your warranty, and potentially causing a fitting failure under the sink.

If your home doesn’t already have a PLV on the main supply, this is also worth discussing — see our post on pressure limiting valves in Sydney homes for more on that.

4. Connecting the drain line (reverse osmosis systems only)

Standard carbon filter systems don’t produce wastewater. Reverse osmosis (RO) systems do — they push a portion of water to drain as part of the purification process. That drain line needs to connect to the sink waste or a nearby drain fitting. It’s a relatively minor connection, but it still needs to be done correctly to avoid slow drips or backflow into the system.

For RO systems, there’s also a pressurised storage tank that sits under the sink. The plumber needs to position this so it fits, connects properly to the filter unit, and leaves enough clearance for future cartridge changes.

5. Mounting the filter housing

The filter housing — the canister that holds the cartridges — needs to be secured to the cabinet wall or base, not just left sitting on the floor of the cabinet. It needs to be positioned so the cartridges can be accessed and swapped without having to disconnect anything, and so the inlet and outlet lines run cleanly without kinks or tight bends that restrict flow.

6. Connecting and mounting the tap

Once the hole is drilled and the supply line is connected, the tap body is fitted through the bench and secured from underneath. The feed line from the filter housing connects to the tap. On a dedicated filter tap, this is typically a quarter-inch push-fit or compression fitting. The plumber checks the connection is watertight before moving on.

7. Flushing and pressure testing

A critical part of the appointment is the system flush. Every new system needs to be flushed to activate the filtration media and remove any trapped air or carbon fines from the manufacturing process. The plumber will then verify the flow rate and perform a pressure test to ensure every connection is watertight.

Skipping the flush means the first litres of water out of the tap will be discoloured and taste of carbon. It’s not harmful, but it’s a poor result and a sign the job wasn’t finished properly.

WaterMark certification: not optional

Every component that connects to your water supply — the filter housing, the fittings, the tap, the PLV — must carry WaterMark certification. Under the Plumbing Code of Australia and NSW plumbing regulations, it is a legal requirement that only WaterMark-certified products be installed in a building’s water supply system. A licensed plumber who installs a non-certified product is in breach of their licence conditions and the plumbing code, and faces significant professional and financial consequences if that installation is later identified during an inspection or insurance claim.

This matters for homeowners too. If a non-certified fitting fails and causes water damage, your home insurer may decline the claim on the basis that unlicensed or non-compliant work was carried out.

When you’re buying a filter system, check the product listing for the WaterMark certification number. Reputable systems will display it clearly. If it’s not there, don’t buy it.

What you can do yourself (and what you can’t)

The line in NSW is fairly clear. Any plumbing work that involves connecting to the main water supply must be performed by a licensed plumber. This is a legal requirement under the Plumbing Code of Australia to ensure safety and prevent contamination.

What homeowners can do themselves:

  • Replace a filter cartridge once the system is installed (no tools, no plumbing connections involved)
  • Flush the system between cartridge changes
  • Clean the filter housing exterior

What requires a licensed plumber in NSW:

  • Drilling through the benchtop and installing the tap body
  • Teeing off the cold water supply line
  • Installing or adjusting a pressure limiting valve
  • Connecting the drain line on an RO system
  • Any modification to existing pressurised plumbing fittings

The cartridge swap is genuinely user-serviceable. Cartridges are user-replaceable — you don’t need a plumber for routine cartridge changes. Everything before that point is licensed work.

What the job looks like on the day

For a standard under-sink dedicated filter tap — carbon or twin-stage system, stone benchtop, existing cold supply line accessible — the job typically takes two to four hours. That includes drilling the bench, connecting the supply, mounting the housing, fitting the tap, flushing, and testing.

Reverse osmosis systems take a little longer because of the tank positioning, the drain line connection, and a longer flush cycle. Budget for three to four hours.

Things that add time:

  • Tight cabinet space with awkward pipe runs
  • A PLV that needs to be installed on the main supply, not just the filter line
  • An older kitchen with galvanised or mixed pipe materials that need compatible fittings
  • A stainless sink rather than a stone bench, where the hole location needs to avoid the sink reinforcing ribs

Clearing the cabinet under the sink before the plumber arrives saves time and makes the job easier. Everything else is sorted on the day.

Units and apartments: one extra consideration

If you’re in a strata building, check your by-laws before booking. Some strata schemes require approval for any work that modifies plumbing within the lot, even minor work under the kitchen sink. It’s rare that approval is refused for a filter tap, but getting it in writing before the job starts avoids any strata dispute later.

Also worth checking: whether your building has a water meter for your lot or a shared supply. In some older apartment blocks, the cold water supply under the kitchen sink runs at unusually high pressure because there’s no PLV on the individual lot supply. A plumber can check this quickly on arrival.

A note on older Sydney homes

If your home has galvanised water pipes — common in Sydney houses built before the mid-1970s — a filter system will work harder than it should. If you have old galvanised pipes leaching rust and sediment, a filter will work harder and wear out faster. In that situation, it’s worth having a conversation about the pipe condition before installing a filter. A filter treats the symptom; corroding galvanised pipes are the cause. You may find the better first step is addressing the pipework.

For more on that, see our article on galvanised pipes in older Sydney homes.

What to sort before the plumber visits

  • Choose your filter system and confirm it carries WaterMark certification
  • Decide whether you want a dedicated tap or an inline connection
  • Clear the cabinet under the sink completely
  • Know whether your benchtop is stone, laminate, or timber (this affects the drilling approach)
  • Check your strata by-laws if you’re in an apartment
  • Have the product manual or spec sheet ready so the plumber can confirm the connection requirements before starting

Ready to get it installed properly?

Jasco Plumbing installs water filter taps across Sydney. We’ll check your pressure, confirm the right fittings for your pipe material, drill the bench cleanly, and leave you with a system that’s tested and compliant. Fixed price before we start, no callout fee for new customers.

Call us on 02 5950 5382 or use the contact form to tell us what you’ve got and we’ll give you a straight quote.

GOT A PROBLEM? WE'VE GOT A PLUMBER.

Give us a call or book online. We're across the whole Sydney Region, 7 days a week – ready when you need us.