TL;DR
- Hot water is the second-largest energy cost in most Australian homes, accounting for roughly 25% of total household energy use. Small changes add up.
- Most efficiency gains come from three places: how you use hot water, how your system is set up, and whether the plumbing around it is working properly.
- A system that’s ageing, scaled up, or losing heat through uninsulated pipes will cost more to run regardless of how careful you are with usage.
- If the tips here don’t move your bill, the system itself may need a service, a component replaced, or an honest assessment of whether it’s time to upgrade.
Hot water is the second largest energy user in Australian homes, accounting for roughly 25% of household electricity consumption. That’s a significant slice of your quarterly bill — and a lot of it is recoverable without touching the system itself.
This isn’t a guide about buying a new hot water system. It’s about getting more out of the one you already have. Some of these tips take two minutes. Others are worth doing once a year. All of them are relevant to Sydney homes, whether you’re running a gas storage unit, an electric tank, an instant gas system, or a heat pump.
Start with your thermostat setting
Storage tanks — both gas and electric — keep water hot around the clock. The higher the thermostat, the more energy the system burns maintaining that temperature, and the more heat escapes through the tank walls and pipes.
Setting the thermostat to 60°C for storage tanks provides safe legionella protection while reducing standby losses. Many older systems are set higher than this by default, or have drifted over time. If yours hasn’t been checked in years, it’s worth a look.
On electric systems, the thermostat is usually accessible on the element panel. On gas storage units, it’s typically a dial on the front of the unit. If you’re not sure where it is or what it’s currently set to, that’s a good question for a plumber during a service visit. Don’t adjust a gas system’s internals yourself — that’s licensed work in NSW.
Check what you’re actually losing through the pipes
Hot water cools down the moment it leaves the tank. If your hot water pipes run a long distance before reaching the tap — through a cold roof cavity, under a concrete slab, or along an exposed exterior wall — you’re losing heat on every run. You also end up running the tap longer waiting for hot water to arrive, which wastes both water and the energy used to heat it.
Insulating exposed hot water pipes can reduce heat loss significantly, especially in colder months. Foam pipe lagging is inexpensive and straightforward to fit on accessible runs. For pipes inside walls or under slabs, the fix is less simple — but knowing the heat loss exists helps explain why your system seems to work harder than it should.
If you have a long wait for hot water at a specific tap, mention it when you next call a plumber. It’s sometimes fixable without major work.
Use off-peak electricity if you have an electric storage system
Newer electric storage models with smart controls let you schedule hot water heating for off-peak hours, which reduces running costs. Older systems can often be put on a timer for the same effect, as long as the tank is large enough to hold a full day’s supply.
Off-peak rates in Sydney vary depending on your retailer and tariff. If you’re not sure whether your system is set up to take advantage of cheaper overnight electricity, your energy retailer can tell you what tariff you’re on, and an electrician can check whether the system is wired to a controlled load circuit.
This one change alone can make a noticeable difference to an electric storage system’s running cost — without touching the hardware at all.
Shorter showers move the needle more than anything else
It’s not glamorous advice, but it’s accurate. Showering can account for up to 48% of hot water energy consumption in a household, concentrated in two discrete daily peaks. Cutting two minutes off a daily shower reduces both water use and the energy needed to heat that water.
If you have a gas instant system, shorter showers have an almost immediate effect — the burner only fires when water is flowing. With a storage system, the benefit shows up as a slower tank drain, meaning the system reheats less often through the day.
A water-efficient showerhead helps too. You can save energy and money by reducing how much hot water you use — for example by choosing low-flow showerheads and using eco settings on appliances. A 3-star WELS showerhead uses around 7.5 litres per minute, compared to 15 or more litres per minute for an older unrated head. The hot water saving is proportional.
Fix dripping hot taps promptly
A dripping hot tap wastes more than water. Every drop that escapes has already been heated, which means your system is working to replace it. A slow but steady drip from a hot tap can add a noticeable amount to both your water bill and your energy bill over a month.
In NSW, homeowners can legally replace tap washers and ceramic cartridges themselves on accessible taps. If you’re not confident doing that, or if the valve seat is worn, a licensed plumber can have most tap repairs done in under an hour. It’s one of the jobs that genuinely pays for itself quickly. For more on what’s involved, see our guide on leaking tap repair prep and safety tips.
Flush sediment from the tank once a year
Sediment — mostly mineral deposits from Sydney’s water supply — settles at the bottom of storage tanks over time. It acts as an insulating layer between the water and the heating element or gas burner, meaning the system has to work harder and run longer to reach the set temperature.
On electric systems, sediment buildup on the element also shortens its life. A simple annual flush, done by a plumber during a service visit, removes the settled material and lets the system run at its intended efficiency. It takes around 15 minutes and is easy to include in a broader hot water service.
If your system is making a rumbling or popping noise during heating, that’s often sediment. Don’t ignore it — the noise usually means efficiency has already dropped.
Check the anode rod every few years
Storage tanks — both gas and electric — use a sacrificial anode rod to prevent the tank lining from corroding. As the anode degrades, it does its job. But once it’s fully depleted, the tank itself starts to corrode from the inside, which shortens the system’s life and can affect water quality.
Regular anode rod inspections in metal tanks prevent corrosion and extend system life. Most manufacturers recommend checking the anode every three to five years. Replacing a depleted anode is far cheaper than replacing a corroded tank. It’s a licensed plumber job in NSW, but a straightforward one.
Don’t heat water you’re not using
If you’re going away for more than a few days, turn your hot water system to its lowest setting or switch it off entirely. A storage system left at full temperature for a week while you’re on holiday is burning energy for no reason.
On electric systems, the isolator switch near the unit handles this. On gas storage systems, most have a pilot or vacation mode. On an instant gas system, there’s nothing to turn off — the burner only fires when a tap is opened, so standby loss is already minimal.
Before you leave, it’s also worth doing a quick check of the system and nearby taps for any drips or minor leaks you might not have noticed. Our pre-holiday plumbing checklist covers what to look for.
If you have a heat pump, timing matters
Heat pumps extract ambient heat from air to heat water, using significantly less energy than conventional electric systems. But they work most efficiently when the air around them is warmer. Morning and evening operation maximises heat pump efficiency by taking advantage of warmer air temperatures.
If your heat pump has a timer or smart controller, set it to run during the warmer part of the day rather than overnight. In Sydney’s climate, this is a practical option for most of the year. Taking advantage of off-peak electricity rates where available helps minimise strain on the system, and a Wi-Fi control system can let you adjust heating schedules remotely for optimal performance.
If you have solar panels, use them to heat water
Using an electric hot water system in combination with a solar photovoltaic (PV) system is an effective way to reduce energy bills and largely eliminate greenhouse gas emissions from hot water. If you already have rooftop solar, running your electric storage system or heat pump during peak solar export hours — typically mid-morning to early afternoon — means you’re heating water with electricity you’d otherwise be feeding back to the grid at a lower rate.
A smart timer or load controller can automate this. It’s worth discussing with a licensed electrician if you’re not already doing it.
The NSW rebate question: is now the right time to upgrade?
If your system is old, undersized, or already showing signs of wear, efficiency tips will only get you so far. At some point, the running cost gap between an ageing electric storage tank and a modern heat pump becomes too wide to ignore.
In NSW, eligible households may receive an upfront discount when replacing an existing electric or gas water heater with an eligible heat pump. The NSW Government lists indicative discounts of up to $640 for replacing an electric water heater and up to $330 for replacing a gas water heater. Federal Small-scale Technology Certificates (STCs) can also reduce the upfront cost further on eligible heat pump and solar hot water systems.
A signed nomination form is required before installation — work completed first cannot be incentivised afterwards. So if you’re considering an upgrade, get the paperwork in order before the plumber starts.
For a broader look at when upgrading actually makes financial sense, see our post on when upgrading your hot water system pays off.
When the tips stop working: signs the system is the problem
If you’ve worked through the list above and your energy use hasn’t shifted, the system itself is probably the bottleneck. Common culprits include:
- A failing thermostat that’s cycling the element or burner more than it should
- A degraded element that’s drawing power but not heating efficiently
- A tank that’s too small for the household, causing constant reheating
- Significant scale or sediment that a flush alone won’t fix
- A system that’s simply past its useful life
For more on what actually shortens a hot water system’s life in Sydney conditions, see our guide on what actually shortens your hot water system’s life.
Get it assessed properly
Most of the checks above are things you can do yourself. But if you’re not sure what you’re looking at, or if the system is making noises, losing pressure, or producing water that’s not as hot as it used to be, it’s worth having a licensed plumber take a look before the problem gets worse.
We work across all of Sydney and can assess your hot water system, carry out a service, or give you an honest answer on whether repair or replacement makes more sense for your situation. Call us or book online — no callout fee for new customers.