Instant Gas Hot Water: Which Sydney Households Actually Benefit

Plumbing Tips

TL;DR

  • Instant gas hot water heats water only when a tap opens — no tank, no standby heat loss, no running out mid-shower.
  • It suits busy households on natural gas connections, homes short on space, and anyone replacing an existing continuous-flow unit.
  • It’s not the best fit for every property. Single-person households, LPG-only properties, and homes running multiple outlets simultaneously at high volume need careful sizing or a different system type.
  • The unit must be sized to your actual simultaneous demand — “continuous flow” means continuous duration, not unlimited litres per minute.
  • Installation and all gas connections are licensed work in NSW. It’s not a DIY job.

Most people start researching instant gas hot water after one of two things: their old storage tank finally gives up, or they’ve had one too many cold showers when someone else beats them to the bathroom. Both are reasonable triggers. But the question worth asking before you buy is whether this system type actually suits the way your household runs — not just whether it sounds good in theory.

This guide works through the fit question honestly, household by household.

How it actually works (the short version)

An instant gas system — also called a continuous flow or tankless unit — has no storage tank. When you open a hot tap, cold water flows through a heat exchanger inside the unit, a gas burner ignites automatically, and hot water comes out the other end. The core benefits of that setup are well documented: no standby heat loss, compact wall-mounted footprint, and hot water that doesn’t run out based on tank size.

What matters here is the nuance: the system heats water continuously for as long as you need it, but only up to its rated flow capacity. A 20L/min unit can supply 20 litres of hot water per minute. If two showers and a dishwasher run simultaneously and that exceeds the unit’s output, you’ll notice.

The households it suits best

Busy family homes on natural gas

This is the sweet spot. A family of four or five with staggered morning routines, a couple of showers running close together, and a dishwasher going in the evening is exactly what a properly sized instant gas unit handles well. For most families, gas systems win out thanks to faster flow rates and lower running costs. The key phrase there is “properly sized” — a 26L/min or 32L/min unit for a busy household, not the smallest model on the shelf.

Homes replacing an existing continuous-flow system

If your property already has a continuous-flow gas unit, swapping like-for-like is usually the most straightforward upgrade path. The gas line is already there, the wall penetrations exist, and the install is simpler than switching system types. You get a newer, more efficient unit with a longer expected lifespan without rerouting anything significant.

Properties short on space

A wall-mounted instant unit takes up a fraction of the space a storage tank does. For a terrace with no side access, a unit tucked into a tight laundry, or an apartment where the hot water cupboard is genuinely cramped, the compact footprint matters. The compact wall-mounted design saves space and suits space-constrained properties.

Renovation projects where the layout is changing

If you’re moving a bathroom or adding one, an instant unit gives you more flexibility on where the system sits relative to the new fixtures. There’s no tank to relocate. That said, the further the unit is from the tap, the longer the wait for hot water to arrive — worth factoring in during the design stage.

The households where it’s a harder fit

Single-person households and low-usage properties

Instant systems aren’t always worth it for low usage. They shine in busy households with lots of showers and baths. If you live alone and your hot water demand is modest and irregular, a smaller electric storage unit or a heat pump might deliver better value over time. The running cost savings from avoiding standby heat loss are real, but they’re smaller when demand is low to begin with.

LPG-only properties

Instant gas units work on LPG as well as natural gas, but the economics shift. LPG is more expensive per unit of energy than natural gas in most Sydney areas, which narrows the running cost advantage over electric alternatives. If you’re on bottled gas and weighing options, it’s worth getting a comparison quote for a heat pump system before committing.

Homes with very high simultaneous demand

Continuous flow does not mean unlimited flow. It means continuous duration, as long as demand stays within the unit’s capacity. A large household where three or four hot outlets run at exactly the same time needs a correctly sized unit — or two units. Getting this wrong is the most common source of disappointment with instant gas systems. The fix is straightforward: size the unit to your real peak demand, not your average demand.

The sizing question most people skip

Flow rate is measured in litres per minute. A standard shower runs at roughly 7–9 L/min. A bath tap at full flow can hit 15–20 L/min on its own. A 16L/min unit might handle one shower and a tap comfortably. A busy family bathroom plus a kitchen tap running simultaneously might need a 26L/min unit or larger.

The right approach is to work out the number of outlets likely to run at the same time during your household’s peak period, then size accordingly. A licensed plumber can do this properly before you buy anything. Buying a unit and then finding it undersized is an avoidable and expensive mistake.

The gas policy question worth thinking about

NSW is gradually moving toward electrification in new builds, and some buyers and renovators are factoring that into long-term decisions. An instant gas system installed today will likely serve 15–20 years without issue. Instantaneous gas scores highest among fuel-burning units because it heats only what you use. But if your household is already heading toward all-electric — solar panels on the roof, no other gas appliances left — it’s worth at least pricing a heat pump alternative before locking in a new gas connection or extending an existing one.

For homes already on natural gas with multiple gas appliances, the calculus is different. The infrastructure is there, the running costs are lower than electric storage, and the system performs reliably year-round in Sydney’s climate.

What the installation actually involves in NSW

Installing or replacing an instant gas hot water system is licensed work. The gas connection, the flue, the pressure relief valve, and the compliance certificate all require a licensed gas fitter and plumber. In NSW, this also means a certificate of compliance is issued once the work is done and tested.

Continuous flow gas systems heat water only when you turn the tap on — no tank, no standby heat loss, no running out mid-shower. But that performance depends on the installation being done correctly: right unit size, correct gas pressure at the meter, proper flue location, and isolation valves in the right places.

The install itself is usually a single visit for a like-for-like swap. Changing system types — say, from electric storage to instant gas — takes longer and may involve running a new gas line if one doesn’t already reach the hot water location.

If you’re not sure which system type suits your property, or you want a fixed price before committing, our hot water system service page covers what we work on and how to get a quote.

A quick way to work out where you sit

Your situation Likely fit
Family of 3+ on natural gas, staggered morning showers Strong fit — size for peak demand
Replacing an existing continuous-flow unit Strong fit — straightforward swap
Tight space, no room for a tank Good fit — compact footprint helps
Single person, low and irregular hot water use Weaker fit — consider heat pump or small electric
LPG-only property Works, but compare heat pump running costs first
3+ outlets running simultaneously at full flow Possible — needs careful sizing, possibly two units
Moving toward all-electric household Worth pricing a heat pump before committing to gas

The honest takeaway

Instant gas hot water is a genuinely good system for the right household. It delivers hot water on demand, uses no energy when nobody’s home, lasts longer than most storage tanks, and handles busy morning routines without complaint — provided the unit is sized correctly and the gas supply can support it.

It’s not the automatic right answer for every property. The households that get the most from it are the ones that match the system to their actual demand, not just their aspirations. Get the sizing right, use a licensed plumber for the install, and it’ll likely be the last hot water decision you make for 15 years or more.

If you want a straight answer for your place — what size, what brand, what it’ll cost, and whether gas is the right call — call us or book online. We’ll give you a fixed price before any work starts.

GOT A PROBLEM? WE'VE GOT A PLUMBER.

Give us a call or book online. We're across the whole Sydney Region, 7 days a week – ready when you need us.