TL;DR
- Adding an ensuite isn’t just a building job — the plumbing is the part that decides whether the project is straightforward or complicated. Where your drainage stack sits relative to the new room is the single biggest factor.
- You’ll need a licensed plumber to rough in new waste and water supply lines, install a floor waste, connect to the existing drainage system, and sign off on a Certificate of Compliance before anything gets tiled over.
- In NSW, all plumbing and drainage work in a new ensuite must be done by a licensed plumber. Waterproofing must comply with AS 3740. Neither is optional.
- The earlier a plumber is involved in the planning, the less likely you are to hit expensive surprises once the walls are open.
The question most people ask last
Most homeowners start planning an ensuite with the fun stuff — the tiles, the vanity, the showerhead. The plumbing gets treated as something to sort out once the layout is locked in. That’s the wrong order, and it’s the reason a lot of ensuite additions end up costing more than expected.
The plumbing doesn’t just connect to the room. It determines what the room can be. Where the waste stack is, how far the new fixtures sit from it, what’s under the floor, and whether the existing hot water system can handle the load — these questions need answers before you finalise a floor plan, not after.
This article covers what a plumber actually needs to do when adding an ensuite from scratch in a Sydney home, and what you need to know before work starts.
First: is the location feasible from a plumbing standpoint?
Not every bedroom wall is equally practical for an ensuite. The main constraint is drainage.
Waste from a shower, basin, and toilet all needs to flow by gravity to your home’s main sewer line. A licensed plumber can tell you where the nearest waste stack is and how much work it’ll take to run drainage to your new ensuite. The closer you are to the main stack, the simpler and cheaper the job.
In a single-storey Sydney home, drainage usually runs under the concrete slab or through a suspended timber floor to the main sewer connection at the boundary. Adding an ensuite on the opposite side of the house from the stack means running waste pipes a long distance — with the correct fall maintained the entire way. Waste pipes must fall at the correct gradient (usually 1:60 in Australia) to keep wastewater flowing smoothly to the main line. Get this wrong, and blockages are almost guaranteed.
In a two-storey home, the question is whether you’re adding the ensuite above an existing wet area (which usually makes drainage easier) or above a dry area like a living room (which adds complexity and cost).
The honest answer to “can we put it here?” requires a plumber to look at your actual house — not a builder’s estimate based on a floor plan.
The plumbing work involved in a new ensuite
When there’s no existing bathroom nearby, adding an ensuite means installing everything from scratch. Here’s what that actually covers.
Drainage rough-in
This is the most involved part of the job. Before any waterproofing or tiling, a plumber needs to install the waste pipes for every fixture: the shower floor waste, the basin waste, and the toilet pan connector. Vertical stacks are installed within wall cavities or chases, extending through the roof for venting and connecting to under-slab drainage. Branch lines connect individual fixture waste pipes to the main stacks, maintaining the specified gradient for gravity flow.
In a slab home, this usually means cutting into the concrete to lay drainage pipes underneath, then making good the slab before the floor can be waterproofed and tiled. In a timber-floor home, the plumber works through the subfloor space, which is generally less disruptive.
The toilet is the most demanding fixture to position. It needs a larger-diameter waste pipe (typically 100mm), and its location is harder to shift once the rough-in is done. Get the toilet position confirmed with your plumber before the framing goes up.
Vent pipes
Every drainage system needs venting. Vent pipes allow air into the drainage system, prevent siphonage of fixture traps, and equalise atmospheric pressure — which ensures smooth flow of wastewater and prevents sewer gases from entering the home. Vent pipes extend through the roof.
In a new ensuite, the vent stack usually needs to be extended or a new vent run added. This is part of the rough-in, not an afterthought.
Water supply lines
Hot and cold supply lines need to be run to the shower, basin, and toilet cistern. Isolation valves should be installed at key points — including individual bathroom branches — for future maintenance. This means if a tap or fitting fails later, the ensuite can be isolated without shutting water off to the whole house.
If the new ensuite is a long run from the hot water system, your plumber may flag that the pipe diameter or system capacity needs review. A continuous flow gas unit that was sized for one bathroom might struggle with two running simultaneously in a larger household.
Floor waste
A floor waste gully is required in a shower wet area. The NCC 2022 prescribes performance and deemed-to-satisfy requirements for wet area applications and sanitary plumbing and drainage systems. Floor wastes are required to be installed in certain wet area applications, and the falls required across a floor surface are prescribed in the Building Code of Australia. Your plumber will position the floor waste and confirm the floor falls are correct before waterproofing goes down.
Waterproofing
Waterproofing isn’t a plumbing task, but it’s closely tied to the plumbing sequence. The rough-in must be complete and inspected before waterproofing is applied. Waterproofing must comply with AS 3740, the Australian Standard for wet area waterproofing. This applies to the shower recess, the floor around it, and the walls to a specified height. It must be done by a licensed waterproofer and is inspected before tiling.
If waterproofing is skipped or done poorly, water gets behind the tiles and into the subfloor or wall framing. That’s not a cosmetic problem — it’s structural damage that can take years to show and cost far more to fix than the original job.
The sequence that matters
One of the most common mistakes in an ensuite addition is getting the trade sequence wrong. Here’s the order that keeps the job on track:
- Plumber assesses feasibility — drainage proximity, floor type, hot water capacity, and stack location confirmed before any building work starts.
- Framing and structural work — walls go up once the plumber has confirmed fixture positions.
- Plumbing rough-in — waste pipes, supply lines, vent stacks, and floor waste installed inside the walls and floor before anything is closed in. Rough-in plumbing starts once framing is complete but before walls or flooring go in. Locking in fixture locations, drain slopes, and correct venting at this point stops future leaks, blockages, or costly repairs.
- Inspection — all installations must follow NSW plumbing standards, with layout inspections and pressure tests required before anything gets sealed.
- Waterproofing — applied after rough-in is inspected and approved, before tiling.
- Tiling and fit-out — tiles go down once waterproofing is cured and passed.
- Final fix — fixtures connected, taps fitted, toilet installed, everything tested.
- Certificate of Compliance — issued by the licensed plumber and lodged with Sydney Water.
Skipping or rushing any of these steps creates problems that are expensive to fix once the tiles are on.
NSW compliance: what’s required
Under the NSW Home Building Act, all plumbing, drainage, electrical, and waterproofing work must be carried out by licensed contractors. There’s no grey area here. A handyman, a builder without a plumbing licence, or a homeowner doing it themselves cannot legally connect drainage, install a toilet, or run new water supply lines.
All bathroom plumbing in Sydney must be carried out by a licensed contractor registered with NSW Fair Trading. Any work affecting drainage, sewer connections, or hot water systems requires a Certificate of Compliance lodged with Sydney Water.
Without this certificate, the renovation cannot legally be considered complete, and future buyers, insurers, or strata committees can demand rectification at your expense.
If you’re in a strata building, add another step: if you’re converting part of a bedroom into a new ensuite, or if the property is in a heritage conservation area or is strata titled, you may need additional approvals. Check with your strata manager before any work starts.
Do you need council approval?
In most cases, internal renovation work that doesn’t change external walls or the building footprint falls under Complying Development in NSW, which is faster than a full Development Application. A Complying Development Certificate (CDC) is typically the pathway for an ensuite addition inside an existing bedroom.
That said, every property is different. Heritage-listed homes, dual-occupancy properties, and strata buildings can all have different requirements. Always check with a licensed certifier before starting work.
Your plumber handles the plumbing compliance side. The building approval side is separate and usually sits with your builder or a private certifier.
What makes an ensuite addition more complicated
Some jobs are straightforward. Others aren’t. These are the things that add time and cost to the plumbing scope:
- Distance from the main stack. A long waste run means more pipe, more falls to maintain, and more potential for problems down the track.
- Concrete slab floors. Cutting and making good a slab is more disruptive and more expensive than working through a suspended timber floor.
- Two-storey homes with the ensuite above a dry area. Drainage needs to be boxed or concealed through the ceiling below, which adds complexity and affects the room underneath.
- Older Sydney homes with ageing pipework. Smart planning saves time, especially in older Sydney homes where outdated pipes can complicate repairs or future upgrades. If the existing drainage or supply lines are in poor condition, a plumber may recommend upgrading them while the walls are open — which is the right time to do it.
- Hot water capacity. Adding a second bathroom to a home with a small storage tank or an undersized continuous flow unit may require a hot water upgrade. Worth confirming before the ensuite is finished and someone stands under a cold shower.
What you can sort before the plumber visits
You can’t do the plumbing yourself, but there are things worth sorting before the first site visit:
- Know roughly where you want the ensuite to go, and which bedroom it will adjoin.
- Know what fixtures you want: shower only, or shower plus toilet and basin?
- Find out where your main sewer inspection point is — usually a round cap near the house boundary or in the yard.
- If you’re in a strata building, have your strata by-laws ready and know whether you need strata committee approval before work starts.
- Know the age of your hot water system and what type it is (storage, continuous flow, heat pump, solar).
The more of this you can answer upfront, the more useful the initial site assessment will be — and the fewer surprises you’ll hit once work begins.
A note on the bathroom plumbing upgrade guide
If you’re renovating an existing bathroom rather than adding a new one, the sequencing and compliance questions are similar but the scope is different. Our bathroom plumbing upgrade guide covers what happens behind the tiles in a renovation context, including moving fixtures, dealing with old pipework, and what the compliance side looks like for an existing wet area.
Ready to work out what your ensuite addition actually needs?
The plumbing feasibility assessment is the right first step — before you finalise a layout, order fixtures, or get a builder’s quote. We can look at where your drainage stack sits, what’s under the floor, and give you a straight answer on what the plumbing scope will involve.
Call Bill or one of the team directly, or use the contact form to tell us what you’re planning and we’ll get back to you with a clear next step.