You’ve patched the same leak twice this year, the hot tap runs brown for a few seconds every morning, and the pressure in the back bathroom has dropped to a trickle. Somewhere between the third repair bill and the last plumber shaking his head, the question changes. It’s no longer “can we fix this pipe?” It’s “is it time to replace the lot?”
That’s a big call, and a fair one. A lot of St George and Shire homes were built decades ago and still run on their original pipework. Here’s an honest look at what replacing old plumbing actually costs, what pushes the price up, and how to work out whether you’re looking at a full repipe or just a targeted repair.
TL;DR
- A full house repipe in Australia usually lands somewhere in the low-to-mid five figures, but the range is wide because every home is different. Get a proper on-site quote before you budget.
- The biggest cost drivers aren’t the pipes themselves. They’re labour, access, how many bathrooms and fixtures you have, single vs double storey, and the wall and floor repairs afterwards.
- Warning signs it’s time: rusty or discoloured water, dropping pressure across the house, and leaks that keep coming back in different spots.
- Old galvanised steel pipe is the usual culprit in older homes. It corrodes from the inside out.
- Partial fixes can buy time, but if the whole system is the same age, you often end up doing it all eventually.
- Want a real number for your place? Talk to us and we’ll give you a fixed price before any work starts.
The short answer on cost
There’s no single figure, and anyone who quotes one over the phone without seeing your house is guessing. What the research does agree on is that a whole-house repipe is a significant job. One Australian cost guide puts a full floor-up replumb broadly in the range of $15,000 to $20,000, with larger or more complex homes running higher. Other guides quote wider ranges depending on whether you’re replacing everything or just sections.
Why the huge spread? Because “replacing old plumbing” means very different things in a two-bedroom unit versus a rambling federation house with two bathrooms and a slab extension. The only way to get a number you can actually plan around is to have a licensed plumber walk through the place and scope the work.
What actually drives the price
Most people assume the pipe material is the main cost. It isn’t. On a typical repipe, around 70% of the total goes toward labour, not materials. Here’s what really moves the number.
How big the house is, and how many fixtures
More bathrooms, more taps, more appliances, more pipe. Larger homes have more fixtures and need longer pipe runs, so they cost more, and multi-storey homes cost more than single-storey because pipe has to run between floors. A single-storey house on stumps with a crawl space is far easier to work in than a two-storey home on a concrete slab.
Access
This is the quiet budget-killer. If your pipes are easy to reach under the floor or in a crawl space, a plumber can move fast. If they’re buried in walls, under tiled floors, or set in a slab, the job gets slower and more invasive. Pipes running inside walls, vertical risers, and lines feeding upstairs bathrooms can mean opening walls and ceilings, working around framing, then paying for patching, paint or tile repairs afterwards.
Putting the house back together
People forget this one. A full repipe isn’t only plumbing work. It’s also the “put the house back together” work: drywall, paint, tile, and sometimes cabinetry or access panels. Budget for it, because it’s real money and it’s often not included in the plumbing-only line of a quote unless you ask.
Pipe material
Material still matters, just less than labour. Copper costs more up front but lasts a very long time. PEX (flexible plastic pipe) is quicker to install and resists corrosion, which is why it’s become a common choice for repipes. If you want the full breakdown of how the materials compare on price and where each one earns its place, we’ve covered that in detail in our guide on copper vs PVC pipes and the real cost difference.
How to tell it’s actually time to replace, not just repair
No single symptom means the whole system has to go. It’s the pattern that tells the story: several problems tracing back to the same cause, which is pipe that’s reached the end of its life. Watch for these.
- Rusty or discoloured water. Brown, orange or reddish water from the tap is one of the clearest signs galvanised steel pipe is corroding from the inside, with rust flaking off the pipe walls into the water. It’s often worst first thing in the morning after water has sat in the pipes overnight.
- Pressure dropping across the house. As galvanised pipe corrodes, the buildup narrows the inside of the pipe and chokes the flow. Corrosion clogs the inside of the pipes and causes loss of water pressure throughout the home.
- Repeat leaks in different spots. One leak in ten years is normal. If you’re calling a plumber every few months for new leaks, the pipes are likely deteriorating.
Age is a strong hint too. Galvanised pipe is typically a dull grey colour and may show rust at the joints, and homes built before the 1970s have a good chance of still running galvanised plumbing. Plenty of older St George and Shire homes fit that description.
Full repipe vs partial: the honest trade-off
A partial repipe (doing the worst runs and leaving the rest) is cheaper today and less disruptive. Sometimes it’s the right call, especially if only one section has failed. But there’s a catch worth being clear-eyed about.
If every pipe in the house was installed at the same time, it’s all on the same clock. Replacing pipes section by section can lead to inconsistent water pressure, mismatched materials, and recurring labour costs. A lot of homeowners who do a patch-up end up back doing the full job within a few years, and by then they’ve paid the access and make-good costs twice.
Our approach is to tell you straight which one your place actually needs. If a focused repair will genuinely hold, we’ll say so. If it’s a band-aid on a system that’s failing everywhere, we’ll say that too, and let you decide with the full picture in front of you.
What a repipe looks like on the day
It’s less dramatic than most people fear. The usual sequence:
- Inspection and quote. A licensed plumber checks the condition of the pipes, works out the scope, and gives you a written, fixed price before anything starts.
- New pipes go in first. The typical method is to install the new pipes, transfer the water supply over to the new system, then drain and disconnect the old pipes.
- Testing. The new system gets pressure-tested for leaks before walls and floors are closed back up.
- Make good. Any drywall, tiling or paint disturbed to reach the pipes gets patched and restored.
On timing, a whole-house repipe usually takes between two days and a full week, depending on the size of the home and the existing pipe system. You won’t always be without water the whole time.
A quick word on doing it yourself, and on gas
Replacing water pipe in a home isn’t a DIY job in NSW. It has to be done by a licensed plumber to meet the plumbing code, and getting it wrong can mean leaks inside your walls, failed inspections, and insurance headaches. If your old home also has ageing gas lines, that work is strictly for a licensed gas fitter. Never touch gas pipework yourself. If you smell gas, turn the supply off if it’s safe to do so and call a licensed professional. You can read more about what’s involved on our gas fitting page.
Before you commit, get a proper diagnosis
The worst outcome is spending five figures on a repipe you didn’t fully need, or spending on repairs that were never going to hold. A camera down the drain lines and a proper inspection of the supply pipes takes the guesswork out. If your problems are drainage rather than supply, a CCTV drain inspection can show exactly what’s happening inside the pipe before anyone quotes a fix. And if it turns out the trouble is a single failing section, that’s often a straightforward repair rather than a full job.
The bottom line for St George and Shire homeowners
Replacing old plumbing is a real investment, usually into the tens of thousands for a full repipe, and the figure swings hard on your home’s size, layout, access, and how much make-good the walls and floors will need. If you’re seeing brown water, falling pressure, and leaks that keep coming back in an older home, it’s worth getting it properly assessed rather than paying for repair after repair.
We’re a family-run local team, not a franchise. Call us and you get me or one of my licensed guys having a proper look, explaining what your place actually needs in plain English, and giving you a fixed price before any work starts. Tell us what’s going on and we’ll give you an honest answer, even if that answer is “you don’t need a full repipe yet.”